Thermo Scientific 1300 Series User Manual Download Page 48

Page: 48 / 130

1300 Series A2

6-3

Thermo Scientific

Section 6

Maintenance

Caution

Remote alarm systems can be retrofitted and integrated into the

unit controls. Specifically, modifications to the filter system and resulting
changes of the airflow may impair personal and product protection. Such
work must be performed only by authorized service personnel.

Replacements and

Repairs

UV light

Chamber light

Figure 6-1.

Light Replacement

Optional UV Lights (Cont.)

3. Wear protective gloves to prevent skin oils from burning into the bulb.

The UV bulb is installed in rotating sockets. To remove, rotate the
bulb counterclockwise to disengage the latch and remove it from the
sockets.

4. To install, slide the bulb contact pins into the rotating socket grooves

and rotate the bulb clockwise to latch the sockets.

Summary of Contents for 1300 Series



































































































































Search results

Summary of Contents for 1300 Series

Reviews:

Related manuals for 1300 Series

Brands by name

Popular brands

Thermo Scientific 1300 Series, User Manual

Search results

Summary of Contents for 1300 Series

Reviews:

Related manuals for 1300 Series

Brands by name

Popular brands