![background image](http://html1.mh-extra.com/html/thermo-king/t-1000r/t-1000r_maintenance-manual_1104339108.webp)
Operating Instructions Standard HMI
7-6
Then the unit running time hourmeters are shown for 30 seconds. The diesel engine run time hours and Diesel Icon are shown in
the upper display. If the optional Electric Standby Feature is installed, the electric motor run time hours and Electric Icon are
shown in the lower display.
A Full Pretrip Test is initiated from this display by pressing and holding the Pretrip Key as shown later in this section.
Electric Motor Run Time Hours
and Electric Icon
When the unit is ready to run the Standard Display of box temperature and setpoint appears. The box temperature and Box Temp
Icon are shown in the upper display. The setpoint and Setpoint Icon are shown in the lower display. The box temperature shown
in Figure is 2.1 C (35.8 F) with a 1.6 C (35 F) setpoint.
Standard Display of Box temperature and Setpoint
Pressing the OFF Key stops unit operation. The unit shuts down immediately and the display goes blank. To start the unit again,
press the ON Key.
Off Key
The Standard Display
The Standard Display is the default display that appears if no other display function is selected. The Standard Display shows the
box temperature and setpoint. The box temperature is that measured by the return air sensor. The box temperature and Box
Temperature Icon are shown in the upper display. The setpoint and Setpoint Icon are shown in the lower display. The box
temperature in Figure is 2.1 C with a 1.7 C setpoint.
Standard Display
Changing the Setpoint
From the Standard Display, press the UP ARROW Key and/or DOWN ARROW Key until the desired setpoint is shown.
1. On Key
2. Red Alarm LED
3. Setpoint
4. Box Temperature
5. UP Arrow
6. Off Key
7. Cycle Sentry/Continuous
Run
8. High Speed Lockout
9. Defrost
10. Pre-trip Test
11. Enter
12. Down Arrow
1
2
3
4
5
6
7
8
9
10
11
12
Summary of Contents for T-1000R
