background image

19

D

00000

3

48

0

3

1

1  Fixing screws on casing ring

The casing ring is fastened with screws.

f

f

Undo the fixing screws on the casing ring.

f

f

Remove the condensate drain bend and pipe collar of the drain. Turn anti-clockwise to undo them.

!

 

Material losses

Inside the appliance, an earth cable is connected to the casing ring. Undo the earth cable in order to 
be able to remove the casing ring.

D

00000

3

48

14

The casing ring overlaps along the joint. A tab on one end clips into the recess at the other end of the casing 
ring.

f

f

Ease the casing ring apart, until it can be removed or slid downwards.

 

Note

Refit the casing ring after completing the work. See chapter "Maintenance and cleaning

 

/ Fitting the 

casing ring").

Cleaning the evaporator

!

 

WARNING Injury

The evaporator consists of numerous sharp-edged fins.

f

f

Be careful when cleaning the evaporator and wear protective clothing, especially safety gloves.

In order to maintain the appliance performance as best as possible, check and clean the appliance evaporator 
as often as necessary.

f

f

Undo the screw that fastens the appliance cover to the top of the fascia.

f

f

Remove the fascia and the appliance cover.

f

f

Carefully clean the evaporator fins. Only use water and a soft brush for this. Never use acidic or alkaline 
cleaning agents.

Summary of Contents for X Hybrid 220





























Reviews: