background image

Page 5 of 14 

 

Recommended Ground Method 

 

This air conditioner must be grounded. This air conditioner is  

 

equipped with a power supply cord having a grounded 3 prong 
plug. To minimize possible shock hazard, the cord must be 
plugged into a mating, grounded 3 prong outlet, grounded in 
accordance with all local codes and ordinances. If a mating outlet 
is not available, it is the customer’s responsibility to have a 
properly grounded 3 prong outlet installed by a qualified electrical 
installer.  
 
It is the customer’s responsibility to: 
 

 

Contact a qualified electrical installer. 

 

Assure that the electrical installation is adequate and in 

conformance with National Electrical Code, NNSI/NFPA 70- 
latest edition, and all local codes and ordinances. 

 
Copies of the standards listed may be obtained from: 
 

National Fire Protection Association 

 One 

Batterymarch 

Park 

 Quincy, 

MA 

02269 

 

LCDI Plug and Power Cord   

 

 

 

To Test Your LCDI Power Cord

 

 

 

 

 

 

 

 

 

 

NOTE: 

Your unit’s device may differ from the ones shown. 

 

1.  Plug power supply cord into a grounded 3 prong outlet. 

 
       2. 

 

Press 

RESET

on some devices, a green light will turn on

 

 
 

 

 

 

 

 

 

3.  Press TEST (Listen for a click; Reset button will trip, and on some devices,  

a green light will turn on). 

 
 

 

 

 

 

 

 

4.  Press and release RESET (Listen for a click; Reset button will 

 

 

 

 

 

 

 

     Latch and remain in). The power supply cord is ready for operation. 

 
 

 

 

 

 

 

 

NOTES: 

 
 

 

 

 

 

 

 

 

 
 
 
This room air conditioner is equipped with a power supply cord 
required by UL. This power supply cord contains state-of-the-art 
electronics that sense leakage current. If the cord is crushed, the 
electronics detect leakage current, and power will be 
disconnected in a fraction of a second. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

The reset button must be pushed for proper operation

 

The power supply cord must be replaced if it fails to 
trip when the test button is pressed of fails to reset 

 

Do not use the power supply cord as an off/on switch. 
The power supply cord is designed as a protective 
device. 

 

A damaged power supply cord must be replaced with 
a new power supply cord obtained from the product 
manufacturer and must not be repaired. 

 

The power supply cord contains no user serviceable 
parts. Opening the tamper-resistant case voids all 
warranty and performance claims. 

Summary of Contents for 420-0030















Reviews: