Thermal Dynamics PAK 200 Operating Manual Download Page 58

Page: 58 / 114

MAINTENANCE

5-2

Manual 0-5057

PAK 200

5.02 Coolant Replacement Procedure

Replace coolant as follows:
1. Disconnect the system from MAINTENANCE input power. At the bottom of the coolant tank, disconnect the

coolant line fitting and collect coolant in a disposable container.

2. Connect the system to MAINTENANCE input power and turn it on to allow the pump to empty the tank,. The

pump will run approximately for 20 seconds before the flow switch causes an interlock. This procedure may

be repeated a few times until the tank is completely empty.

3. Connect the coolant line fitting and fill the tank with fresh coolant until the right level is reached.

RETURN

SUPPLY

RETURN

SUPPLY

Art # A-04803

COOLANT

Fill Range

Coolant Tank

4. Turn system on, let it run for a few minutes and check coolant level, refill if necessary.

Summary of Contents for PAK 200



















































































































Search results

Summary of Contents for PAK 200

Reviews:

Related manuals for PAK 200

Brands by name

Popular brands

Thermal Dynamics PAK 200, Operating Manual

Search results

Summary of Contents for PAK 200

Reviews:

Related manuals for PAK 200

Brands by name

Popular brands