background image

 

ELECTRIC COMBINATION BOILER 

  

 

 (European Patent No: 1757678.  Design Right Protected.) 

 

TH9- 210U, TH9-250U, TH9-330U 

MRK 2

 

TH12-210U, TH12-250U, TH12-330U 

MRK 2

 

 

INCLUDES THERMAL SOLAR & WOOD BURNING STOVE WITH WATER JACKET APPENDIX 

 

This product is suitable for connection to ~230-240V, 50Hz 

 

INSTRUCTIONS FOR USE, INSTALLATION AND 

SERVICING 

for all models with serial No beginning 

4-

 

TO BE LEFT WITH THE USER 

 

The instructions consist of three parts; 

User

Installation

 and 

Servicing

 instructions, which include the guarantee registration 

card.  
 
The instructions are an integral part of the appliance and must, to comply with the current issue of the building, electrical 
regulations and water by-laws, be handed to the user on completion of the installation. 
 

GUARANTEE REGISTRATION 

Thank you for installing a new Thermaflow product in your home. 
 
Thermal innovations appliances, are manufactured to the very highest standards so we are pleased to offer our customers, a 
comprehensive first year guarantee and a second year parts guarantee. 
 
In the instruction envelope is to be found your guarantee registration card, which must be completed and returned to Thermaflow 
Ltd or register your Thermaflow appliance for 1st year guarantee protection by calling the below number. 
 
Our guarantee gives you peace of mind valuable protection against breakdown by covering the cost of- 

 

All replacement parts 

 

All labour charges 

 

All call-out charges 

 
 
 

THERMAFLOW LTD 

31-39 Napier Court, Cumbernauld, Glasgow, G68 0LG 
 

Customer services 
Tel  

+44 (0) 870 850 5207 

Fax 

+44 (0) 870 850 5208 

Web www.thermaflowheating.co.uk 

 

Issue Number: 2b   Issue date: February 2012 

 

Copyright Notice 

This document contains proprietary information protected by copyright, and this Manual and documentation are copyrighted. All rights are reserved. No part of this 
document may be photocopied or reproduced by mechanical, electronic, or other means in any form without permission from Thermaflow Ltd. 

 Copyright Thermaflow Ltd 2006-12 -All rights reserved. 

Summary of Contents for TH12-210U MRK 2





































Reviews: