background image

23 

 

PROBLEM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

When igniter knob is 
pressed in there is no 
spark at ODS/pilot.

 

 

 

Igniter electrode is 
positioned wrongly. 

 

Cables between switch, 
battery pack, igniter and 
igniter electrode may be 
loose, pinched, wet or 
broken. 

 

Bad igniter 

 

No battery or battery used 
out. 

 

Reposition igniter electrode. 

 

Secure or replace cables 
between switch, battery pack, 
igniter and igniter electrode. 
 
 
 

 

Replace igniter. 

 

Install or replace battery. 

 

 

When igniter knob is 
pressed in there is a 
spark at ODS/pilot but 
no ignition.

 

 

 

Gas supply is turned off or 
equipment shutoff valve is 
closed. 

 

Control knob not fully 
pressed in while pressing 
igniter button. 

 

Air in gas lines when 
installed. 
 

 

ODS/pilot is clogged. 
 

 

Control knob not in PILOT 
position. 

 

External shut off valve on 
gas supply opened too fast 
and blocked appliance 
regulator in heater. 

 

Turn on gas supply or open 
equipment shutoff valve. 
 

 

Fully press in control knob while 
pressing igniter button. 
 

 

Continue holding down control 
knob. Repeat igniting operation 
until air is removed. 

 

Clean ODS/pilot or replace 
ODS/pilot assembly. 

 

Turn control knob to PILOT 
position. 

 

Close external shut off valve 
and re-open slowly. 

 

ODS/pilot lights but 
flame goes out when 
control knob is released.

 

 

 

Both control and igniter 
knobs are not fully pushed 
down. 
 

 

Thermocouples are not 
heated enough.   
 

 

External shutoff valve of gas 
supply is not fully opened. 

 

Thermocouple connections 
are loose or damaged. 

 

Control valve damaged. 

 

Press in both the igniter and pilot 
knobs fully. While holding igniter 
down, set control knob to number 
5. Run heater for 15 minutes.   

 

After ODS/pilot lights, keep both 
knobs depressed for at least 15 
seconds. 

 

Fully open equipment shutoff 
valve. 

 

Secure or replace thermocouple 
connections. 

 

Contact customer service. 

 

Burner(s) does not light 
after ODS/pilot is lit 
stably

 

 

 

Burner orifice is clogged. 
 

 

Burner orifice diameter is too 
small. 

 

Inlet gas pressure is too low. 

 

Clean burner orifice or replace 
burner orifice. 

 

Contact customer service. 
 

 

Contact local gas supplier. 

 

Delayed ignition of 
burner(s).

 

 

Manifold pressure is too low. 

 

Burner orifice is clogged. 

 

Contact local gas supplier. 

 

Clean or replace burner orifice. 

 

Burner backfiring during 
combustion.

 

 

 

Burner orifice is clogged. 
 

 

Burner is damaged. 

 

Gas regulator or/and 
appliance regulator are 
defective. 

 

Clean burner using compressed 
air or replace burner orifice.

 

 

Contact customer service. 

 

Contact customer service. 

 

Slight smoke or odor 
during initial operation.

 

 

Residues from 
manufacturing processes. 

 

 

Problem will dissipate after a few 
hours of operation in high setting.   
Ensure appropriate ventilation 
during this time. 

Summary of Contents for GLDF18T-VF




























Reviews: