background image

quest

Asset Protection and IAQ Solutions

quest

1-800-533-7533 

Quest 

DRY 

150                 Installation, Operation and Maintenance Instructions

  

www.thermastor.com

[email protected]

1.  Intended Application for Quest 

DRY

 150 

For the ideal installation, draw air from the central part of the structure and return it to isolated areas of 
the structure like the rest rooms, utility or mechanical room, or cooking area. The duct work of the existing 
heating system can be used to supply air to the structure. 

2. Specifications

Model:  

 Quest 

DRY

 150  

Indoor Air Quality System 

Electrical:  

 110-120 VAC, 6.9 Amps, 60 Hz, grounded 

Water Removal Capacity:   150 pints/day @ 80°F, 60% RH 

Operating Temp. Range:   56°F min., 100°F max. 

Air Flow:  

415 CFM @ 0.0" WG  

 

365 @ 0.4" WG 

Refrigerant Charge:  

2 lb., R-410.A

Duct connections:  

Round 10" & 6" inlets, 10" outlet (ovaled)

Filter Size:  

 2" X 16" X 16" 

Size (w/o duct collars):  

37" wide X 22" high X 20 5/8" deep

Unit Weight:  

134 lbs.

3. Installation

3.1 Location

The Quest 

DRY

 150 can be installed in a variety of locations to meet the owner's needs as listed below. In all 

cases keep the following cautions in mind:

•    It is designed to be installed INDOORS IN A SPACE THAT IS PROTECTED FROM RAIN AND 

FLOODING.

•    Install the unit with space to access the back and side panels for maintenance and service and also to 

allow easy access to the filter cover panel. DO NOT INSTALL UNIT WITH THE FRONT PANEL OR 
FILTER COVER PANEL INACCESSIBLE.

•    Avoid discharging the air directly at people, or over the water in pool areas.
•    If used near a pool or spa, be certain there is NO chance the unit could fall into the water or be splashed 

and that it is plugged into a GROUND FAULT INTERRUPTER. 

•   DO NOT use the Quest 

DRY

 150 as a bench or table. 

•    DO NOT place the Quest 

DRY

 150 directly on structural members. Provide vibration isolation in order to 

minimize operational vibration and/or noise.

•    A drain pan MUST be placed under the unit if installed above a living area or above an area where water  

leakage could cause damage. 

FOR HVAC INSTALLER AND OWNER ONLY

Summary of Contents for Quest DRY 150



































Reviews: