Theralux Theraflo TVS 1.5hp, Instruction Manual

Page: 9 / 20

9
THERAFLO REPLACEMENT PARTS DIAGRAM THERAFLO REPLACEMENT PARTS TABLE
REF NO. PART NO. DESCRIPTION
1 & 2 THERAF4320 Hand Knob Kit for Strainer Cover (inc Hand Knob &
Swivel Nut)
3 THERAF4304 Strainer Cover, Hand Knob Style - Clear
4 THERAF4303 Strainer Cover O-Ring
5 THERAF4302 Basket
6 THERAF4301B Pump Housing/Strainer - 50mm, w/Drain Plugs, threaded
external
7 & 8 THERAF4318 Drain Plug with O-Ring
9 THERAF4317 Mounting Foot Cap Screw (set of 2)
10 THERAF4316B Mounting Bracket, hps style
11 THERAF4323 Spacer for motor support (required only for 1hp model)
12, 13, 14 THERAF4321 Union Kit (set of 2) suit 40mm & 50mm w/Gasket (T-Seal)
15 THERAF4322 Union Gasket (T-Seal)
16 THERAF4305 Housing Gasket
17 THERAF4323B Diffuser Gasket
18 THERAF4306C Diffuser
19 THERAF4307B Impeller Ring
20 THERAF4308K Impeller 1HPVS (required only for 1hp model)
21 THERAF4309B Seal Assembly (inc, Mechanical Seal and Slinger)
22 THERAF4312B Slinger
23 THERAF4310B Seal Plate
24 THERAF4311B Motor Cap Screw (4 required)
25 THERAF4313B Motor Mounting Plate
26 THERAF4315K Motor 1HPVS (required only for 1hp model)
27 THERAF4314 Housing Cap Screw (6 required)
THERAF4308H Impeller 1.5HPVS (required only for 1.5hp model)
THERAF4315L Motor 1.5HPVS (required only for 1.5hp model)
THERAFLO REPLACEMENT PARTS DIAGRAM THERAFLO REPLACEMENT PARTS TABLE
REF NO. PART NO. DESCRIPTION
1 & 2 THERAF4320 Hand Knob Kit for Strainer Cover (inc Hand Knob &
Swivel Nut)
3 THERAF4304 Strainer Cover, Hand Knob Style - Clear
4 THERAF4303 Strainer Cover O-Ring
5 THERAF4302 Basket
6 THERAF4301B Pump Housing/Strainer - 50mm, w/Drain Plugs, threaded
external
7 & 8 THERAF4318 Drain Plug with O-Ring
9 THERAF4317 Mounting Foot Cap Screw (set of 2)
10 THERAF4316B Mounting Bracket, hps style
11 THERAF4323 Spacer for motor support (required only for 1hp model)
12, 13, 14 THERAF4321 Union Kit (set of 2) suit 40mm & 50mm w/Gasket (T-Seal)
15 THERAF4322 Union Gasket (T-Seal)
16 THERAF4305 Housing Gasket
17 THERAF4323B Diffuser Gasket
18 THERAF4306C Diffuser
19 THERAF4307B Impeller Ring
20 THERAF4308K Impeller 1HPVS (required only for 1hp model)
21 THERAF4309B Seal Assembly (inc, Mechanical Seal and Slinger)
22 THERAF4312B Slinger
23 THERAF4310B Seal Plate
24 THERAF4311B Motor Cap Screw (4 required)
25 THERAF4313B Motor Mounting Plate
26 THERAF4315K Motor 1HPVS (required only for 1hp model)
27 THERAF4314 Housing Cap Screw (6 required)
THERAF4308H Impeller 1.5HPVS (required only for 1.5hp model)
THERAF4315L Motor 1.5HPVS (required only for 1.5hp model)
THERAFLO INSTALLATION
The Ther aflo TVS comes with qui ck r elease connecting unions on both the inlet
and outlet which simplifies the installation process. It also allows the user to
remove the pump at any time by simply unscrewing each union. This is handy for
any future maintenance.
The 2 connecting unions can be plumbed with either 40mm or 50mm PVC pipe.
Ideally, the pump will operate better with the least amount of PVC bends and in
the closest proximity to the swimming pool available. Ensure the suction pipe is
the same size or larger than the discharge pipe.
Installation should be made on a level concrete slab or solid even surface with
the pump either bolted or screwed down.
Ther e should be at least 100mm clea r ance between the r ear of the pool pump
motor to allow for ventilation & cooling.
Connect the sc re w-on union to the pump inlet, clean the surface a r ea with
priming solution, and then glue together, using pressure PVC glue, the PVC
plumbing that comes from the swimming pool skimmer box.
Please note: Do not forget to use the union gasket provided.
Connect the sc re w-on union to the pump outlet, clean the surface a r ea with
priming solution, and then glue together, using pressure PVC glue, the PVC
plumbing line that connects to the filter inlet.
Please note: Do not forget to use the union gasket provided.
Connect the elect r ical pow er ca ble plug into your power supply – this may be a
power point or a salt water/mineral chlorinator.
Please note: Do not turn power on at this point.
Please allow enough time for the glue to set. Please che c k the PVC glue used for
timing directions. However, we recommend you allow 6-8 hours for optimum
results.
All electrical wiring must be performed by a licensed electrical contractor and
must conform to the Latest Edition AS/NZS 3000 Wiring Rules.
THERAFLO START UP
Once the glue has had the required amount of setting time, check that both the
inlet and outlet connection points are hand tight.
At this point, it is necessary to prime the pump wet end. This can be done by
unscrewing the 2 locking knobs & removing the clear plastic lid.
Fill the hair & lint pot area up with water until it is completely full. This can be
pool water via a bucket or tap water from your hose.
Once full, please install the clear lid and tighten the locking knobs hand tight.
Check that ALL valves are in the open position and that your filter multipart valve
is set to FILTER.
It is now time to turn the power on (on the pump). This will either be via a power
point or chlorinator depending on the type of swimming pool you have.
The Theraflo TVS swimming pool pump will automatically start up in priming
speed (high speed) which will last for 5 minutes. Once the pool pump is primed,
you can then select the best suited speed for your swimming pool.
Please note: You need to ensure that you have enough water flow to provide
sufficient filtration for your pool volume & system. The water flow provided can
be adjusted by simply changing the speed of the motor (refer to TVS control
page).
If you have a salt chlorinated pool, you also need to ensure that your salt cell is
always 100% full of water whilst the pump is in operation. If you are unsure of
the above, please consult your local swimming pool professional.