4
Master 1
Master 2
L’
L’
•
One master with individual brightness measurement per
lighting group
•
Set potentiometer individually for each
master
•
Switch up to 10 detectors in parallel
•
Use the phase with the same phase for all detectors
8. Settings
The presence detectors were supplied with basic settings
ready for operation. The specifications are guidance values.
The „SendoPro 868-A“ and „theSendaP“ remote controls are
optionally available for start-up. They enable remote setting
of all potentiometer values settings from a distance.
Switch contact light settings
Potentiometer brightness switching value A „lux“
The required brightness switching value can be set via the lux
potentiometer.
The setting range is around 30 to 1000 lux. The factory pre-
setting is 300 lux.
Brightness switching values from 30 to 3000 lux can be set
via the management remote control.
Teach-in
: When the lux potentiometer is moved to the
teach-in position, the LED start to flash for 20 seconds. As
soon as the LED stops flashing, the current measured bright
-
ness value is accepted as the brightness switching value.
When the teach-in position is exited, the set value on the LUX
potentiometer is accepted as the new brightness switching
value.
Teach-in can also be carried out using the „SendoPro 868-A“
and „theSenda P“ remote controls. In this case, the current
measured brightness value is immediately accepted as the
brightness switching value.
The brightness measurement is deactivated at potentiometer
setting „on“. The channel light then switches only depending
on presence.
Potentiometer lighting time delay
The following guidance values have proved themselves in
practice and are recommended as settings:
•
Transit zones (no work area)
approx. 5 min
•
Classroom
approx. 10 min
•
Work areas (office, meeting room)
approx. 10 min
•
„Pulse“ : Control staircase light time switch (0.5 s „on“ /
10 s „off“)
Parameters and control commands via remote
control
The following parameters can be queried or changed via
the remote control for support during installation as well as
servicing:
Parameter
Description
SendoPro
can be
queried
868-A
SendoPro
be changed
868-A
theSenda
P can be
changed
Brightness
switching
value A
Value range in lux
x
x
x
Measurement off
x
x
x
Time delay
A
Value ranges
in seconds and
minutes
x
x
Pulse
x
x
Short pre-
sence A
On / Off
x
Configura
-
tion type
auto / man
x
x
x
Control
input S
Auto / switch /
push button S /
push button O
x
Detection
sensitivity
(PIR)
Value range in
levels
x
x
Group
address
All / I / II / III
x
x
LED display
movement
Off / On
x
The parameters are sent to the presence detector with the
„SendoPro 868-A“ management remote control or with „the-
Senda P“ installation remote control via infra-red. Changed
parameters are immediately applied and used by the detector.
With the „SendoPro 868-A“ management remote control,
parameters can be queried by sending values level-by-level
to the detector. If the sent values are below the set parame-
ter, the LED illuminates briefly. If the sent values are equal or
above the set parameter, the LED flickers for 2 seconds.
The following control commands can be triggered
with the remote control:
Control command Description
Can be trigge-
red SendoPro
868-A
Can be
triggered
theSenda P
Teach-in channel
A
Activate
x
x
Switch lights
on/off
Lighting group can be
switched on and off.
x
x
Presence test
On / Off
x
x
Restart
Restart detector
x
x
Factory
regulations
Set all parameters
and settings to factory
setting.
x
Brightness switching value A
The brightness switching value defines the minimum desired
brightness. The current prevailing brightness is measured
below the presence detector. If the prevailing brightness is
