Theben RM 4 H FIX1 Page 35 Manual Download

Page: 35 / 41

Switch actuators RM 4 H, RM 8 H

5.1.4

Important parameter settings

Standard or customer-defined parameter settings apply to unlisted parameters.

TA 2 S:
Parameter page Parameter

Setting

Channel 1

Activate channel 1

Yes

Channel 1 function

Push button

Button object 1

Object type

Switching (1 bit)

Send after short operation Send telegram
Value

Change over

Send after long operation Do not send
Send after double-click

Do not send

Channel 2

Activate channel 2

Yes

Channel 2 function

Push button

Button object 1

Object type

Switching (1 bit)

Send after short operation Send telegram
Value

Change over

Send after long operation Do not send
Send after double-click

Do not send

RM 4 H:

Parameter page

Parameter

Setting

Channel C1

Channel function

Switch On/Off

Activation of function via Switch object

Contact characteristics

Type of contact

NO contact

Summary of Contents for RM 4 H FIX1










































Search results

Summary of Contents for RM 4 H FIX1

Reviews:

Related manuals for RM 4 H FIX1

Brands by name

Popular brands

Theben RM 4 H FIX1, Manual

Search results

Summary of Contents for RM 4 H FIX1

Reviews:

Related manuals for RM 4 H FIX1

Brands by name

Popular brands