background image

Parts List

P.2

    1. MAIN WING -- 1 pair

    2. SCREW PB2x20mm -- 4 pcs
        SCREW PB2x16mm -- 2 pcs
        SCREW PB2x22mm -- 4 pcs
        SCREW PB2x18mm -- 2 pcs
        SCREW PWA2x8mm -- 16 pcs
        FUEL TUBE Ø6x5mm -- 8 pcs
        CLEVIS -- 4 pcs
        STRAPER -- 4 pcs
        TRI-HORN M3x14mm (S) (For Aileron & Flap) -- 4 sets
        SERVO MOUNTING PANEL 22x68x78mm (For Aileron) -- 4 pcs
        PUSHROD Ø1.8x95mm w/ Threads (For Aileron) -- 2 pcs
        PUSHROD Ø1.8x110mm w/ Threads (For Flap) -- 2 pcs

    3. WING JOINER 6x20x299.4mm -- 1 pc.

    4. STABILIZER & ELEVATOR -- 1 set
        FUSELAGE -- 1 pc.

    5. VERTICAL FIN & RUDDER -- 1 set
        VERTICAL WING’S FIN 3x40x50mm -- 1 pc.

    6. SCREW PB2x16mm -- 6 pcs
        CLEVIS -- 2 pcs
        FUEL TUBE Ø6x5mm -- 2 pcs
        TRI-HORN M3x14mm (S) (For Elevator) -- 2 sets
        PUSHROD Ø1.8x635mm w/ Threads (For Elevator) -- 2 pcs

    7. SCREW PB2x16mm -- 3 pcs
        CLEVIS -- 1 pc.
        FUEL TUBE Ø6x5mm -- 1 pc.
        TRI-HORN M3x14mm (S) (For Rudder) -- 1 set
        PUSHROD Ø1.8x760mm w/ Threads (For Rudder) -- 1 pc.

    8. ENGINE MOUNT PL5111050 -- 1 set
        SOCKET HEAD SCREW M4x25mm -- 4 pcs
        WASHER d4xD9mm -- 4 pcs
     

    9. FRONT LANDING GEAR -- 1 set
        COLLAR Ø4.1mm w/ set screw -- 4 sets
        SET SCREW M3x3mm -- 4 pcs
        WHEEL PANTS -- 1 pc.
        WHEEL Ø50mm -- 1 pc.
        STEERING ARM Ø4.1mm w/ set screw -- 1 set

 

        FRONT GEAR ABSOREBER ACCESSORIZE -- 1 set
        

  10. FUEL TANK 380cc -- 1 set
        CBLE TIE (For Fuel Tank) 1.5x5x400 -- 1 pc.

 

        DOUBLE - SIDED TAPE 40x100mm -- 1 pc.

  11. SOCKET HEAD SCREW M3x25mm -- 4 pcs
        WASHER d3xD7mm -- 8 pcs
        M3 NUT -- 8 pcs
        THROTTLE PUSHWIRE Ø1.2x370mm -- 1 pc.
        

         PLASTIC TUBE d2xD3x140mm -- 1 pc.
         FRONT WHEEL PUSHROD Ø1.4x260mm -- 1 pc.
         PLASTIC TUBE d2.5xD4x140mm -- 1 pc.
   

   12. MAIN LANDING GEAR -- 1 pair
         MAIN LANDING GEAR COVER -- 1 pair
         SCREW HM4x45mm -- 2 pcs
         

SCREW KA2.3x8mm -- 4pcs

          QUICK RELEASE NYLON RIVET PL1208042 d2xD8mm -- 4 pcs

         SOCKET HEAD SCREW M2.5x16mm -- 6 pcs
         M4 NUT -- 2 pcs
         WASHER d4xD9mm -- 4 pcs
         WASHER d2.5xD8mm -- 6 pcs
         COLLAR Ø4.1mm w/ set screw -- 4 sets
         WHEEL PANTS -- 1 pair
         WHEEL Ø62mm -- 2 pcs
         PLATE 1mm -- 2 pcs

   13. LINKAGE CONNECTOR Ø2.1mm -- 2 sets

   14. WIND SHIELD & SIDE WINDOWS -- 1 set
         SCREW PWA2.3x8mm -- 8 pcs
         SILICON GROMMET d1.5xD6.5mm -- 8 pcs

   15. STRAPER -- 2 pcs
         FUEL TUBE Ø6x5mm -- 2 pcs
         SPONGE 60x70x122mm (For Radio Equipment) -- 1 pc.
         PUSHROD Ø1.8x100mm (For Elevator) -- 1 pc.
         PUSHROD CONNECTOR (For Elevator) -- 1 set

   16. SCREW HM4x30mm -- 2 pcs
         WASHER d4xD15mm -- 2 pcs
         PLYWOOD 2x32.5x130mm (Wing Protection) -- 1 pc.
   

   17. COWLING -- 1 pc.
         TRANSPARENT 3D TEMPLATE -- 1 pc.
         SCREW PWA2.6x12mm -- 8 pcs
         SILICON GROMMET d1.5xD6.5mm -- 8 pcs
         SPINNER Ø52mm -- 1 set
         AIR SCOOP -- 1 set
   

   18. MAIN WING STRUT -- 1 pair
         SOCKET HEAD SCREW M2.5x16mm -- 4 pcs
         WING STRUTS COVER -- 1 set
         BATTERY COVER -- 1 pc.

   19. DECALS A246DEC -- 1 set

COVERING:--

TOUGHLON STL100 WHITE

TOUGHLON STL 580 PEARL BRONZE

LIGHTEX SGX 201 BLACK

LIGHTEX SGX 350 CORSAIR BLUE

A246PO28151211

Summary of Contents for SkyLink 40

















Reviews: