The World Models Manufacturing Happy-Fly Instruction Manual Download Page 10

C. G.

C. G.

19

19

85mm

85mm

3.35 in

3.35 in

The  ideal  C.G. position is  

85mm(3.35 in.)

 behind

the leading edge measured at where the wing meets
the fuselage.  In order to obtain the C.G. specified, 
add weight  to  the fuselage or move the battery 
position.  Check the C.G. before flying.

Important Safety Precautions

Important Safety Precautions

# First time flyer should never fly by himself / herself.  Assistance from experienced flyer is

# First time flyer should never fly by himself / herself.  Assistance from experienced flyer is
   absolutely necessary.

   absolutely necessary.

#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

  pre-adjusted aircraft.

  pre-adjusted aircraft.

#Make sure  the air field is spacious, never  fly the plane too close to people and never get

#Make sure  the air field is spacious, never  fly the plane too close to people and never get
  too close to a running propeller.

  too close to a running propeller.

#If you find wrinkles on the covering as  a  result of  weather changes, you can use hot iron

#If you find wrinkles on the covering as  a  result of  weather changes, you can use hot iron
  to remove  the  wrinkles.  Please begin with lower temperature setting and gradually raise

  to remove  the  wrinkles.  Please begin with lower temperature setting and gradually raise
  the temperature until the wrinkles are gone.  Too hot an iron may damage the covering.

  the temperature until the wrinkles are gone.  Too hot an iron may damage the covering.

#Check and re-tighten up all factory assembled screws, use thread locker if applicable. 

#Check and re-tighten up all factory assembled screws, use thread locker if applicable. 

#

 HAPPY   FLY   20

 

   is  specially  designed to be powered  by  

0.25  2

  stroke  glow

#

 HAPPY   FLY   20

 

   is  specially  designed to be powered  by  

0.25  2

  stroke  glow

   

engine, using a more

   

engine, using a more  powerful engine does not mean better performance.  In fact, over 

  powerful engine does not mean better performance.  In fact, over 

powered  engine may 

powered  engine may cause severe damge and injuries.

cause severe damge and injuries.

A022S0606

Summary of Contents for Happy-Fly













Reviews: