background image

Elevator

Important Safety Precautions

#First time flyer should never fly by himself/herself.

 

 Assistance from experienced flyer is

  absolutely necessary.

#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
  pre-adjusted aircraft.

#                                  is specially designed to be powered by 

geared 

.

  
#Make sure the air field is spacious, never fly the plane too close to people and never get
  too close to a running propeller.

#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
  to remove the wrinkles.

  

Please begin with lower temperature setting and gradually raise 

  the temperature until the wrinkles are gone.

  

Too hot an iron may damage the covering.

#Check and re-tighten up all factory assembled screws, use thread locker if applicable. 

speed 550 motor

Warning!

P.9

Control Throws

C.G

.

12

The ideal C.G. position is 75mm (2

.

95 in.) Behind

 

the leading edge

 measured at  where the wing

 

meets the fuselage.

  

In order to obtain

 the C.G.specified, add weight  to the fuselage or move

 

the battery

 position.

  

Check the C.G. Before

 

flying.

Rudder 

30mm

30mm

15mm

15mm

11

75mm

C.G.

2

.

95in.

Summary of Contents for Blue Bird EP












Reviews: