background image

Starting the Pump and Filter 

System 

t *GTZTUFNJTFRVJQQFEXJUIBOJOMJOF

WARNING

1.
 components; Non-Original clamp 
components may fail in use and 
cause explosive 

component 

separation. Verify that upper and 
lower filter bodies are properly 
secured with the filter body

 

clamp. 

Never rely on hand tightening the 
clamp nut to the clamp bolt. Using a 
¾” socket on a torque

 

wrench, 

torque clamp nut to clamp bolt to 
150 inch-lbs. (See Fig 1) Verify that 
the filter manual air relief

 

body is in 

the LOCK position, and no filter 
components are missing, damaged 
or not genuine 

AquaPro

 

components. (See Fig 2)

Use ONLY Original 

plug requires an o-ring seal. (See 

Fig 4)

2.

Close filter drain. NOTE: Filter

3.

Open all system valves to allow

 water from the pool to the filtration 
system and from the filter to return to

 

the pool.

 

Before Starting the Pump

Starting Pump

1.

When starting system pump,

do not stand over or near filter. If
water leakage appears at filter tank
clamp,

 

immediately turn off all system

circulation pumps and all electrical
power. Do not return to the filter until
all

 water leakage has stopped.

Reassemble the clamp system per
the instructions on page 7 in this
owner’s manual to stop leak.

air relief valve only when a steady 
stream of water (not air or, air and 
water

 mix) is discharged from the 

manual air relief valve.

2.

Return to filter to CLOSE manual

Figure 2

Manual Air Relief shown open

Figure 1

Place the manual air relief valve

4.

in OPEN position. (See Fig 2)

WARNING

OPERATION

FILTERING

Filtration starts as soon as flow is 
steady through the filter. As the filter 
removes
dirt from the pool water, the 
accumulated dirt causes a resistance 
to flow. As a
result, the gauge pressure will rise 
and the flow will decrease. When the
pressure rises between 7 and 10 psi 
(.49 - .69 bar) above the starting 
pressure, or when the flow decreases 
below

 

the desired rate, clean or 

replace the filter cartridge elements. 
Once your filter is running and there 
is a pressure

 reading, line up the 

green arrow with the current reading. 
(See Fig 3) When the pressure rises 
to or above the red 

or second arrow, 

it is time to clean or replace your filter 
cartridge elements.

By recording the initial starting 
pressure (with clean filter

 

elements) a 

determination can be made when the 
filter

 cartridge elements should be 

replaced rather than cleaned. 

After the 

filter elements have been cleaned and 
reinstalled if

 the starting pressure is 

higher than 6 PSI above the starting 

pressure with the new filter cartridge 
elements, the filter

 cartridge elements 

should be replaced the next time the 
gauge arrow reaches the red arrow.

6

Summary of Contents for APF325PRO















Reviews: