background image

NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL
INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

INSTRUCTIONS

UNPACKING AND SET-UP

1. Open carton, then remove ramp, and shipping boards.
2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING 

CABLE RESTRAINT FROM SCISSOR MECHANISM.

3. Connect foot-operated air valve to 110 psi air supply. The lift may be damaged and/or 

personal injury may result if the pressure exceeds the maximum 110 psi rating.

4. Stand clear of lift table and depress the UP side of foot valve to raise table.
5. To lower table, lift detent bar from safety latch and lower to next position or to floor.
6. Mount ramp to lift top by inserting ramp tabs into slots on lift top.
NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.

OPERATION

1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 

months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at 
top ends of inside frame assembly.

4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its 

seal every 6 months.

6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are 

located at the top end of the inside frame assembly.

OTHER OPTIONS AVAILABLE

Separate installation instructions included with each option.

PART # 

DESCRIPTION 

14476 

CV-17 CYCLE VISE

 – Vise with removable wheel stop built into vise  

10728 

12” SIDE EXTENSIONS

 (2) – Expands width of lift from 24” to 48” includes stabilizer 

bar   

16011 

13” FRONT EXTENSION

 – Extends lift top to 93” for longer wheel base motorcycles 

10736 

13” REAR EXTENSION

  – Extends lift top to 93” for longer wheel base motorcycles 

15566 

RAMP END EXTENSIONS

 – Attaches to end of lift ramp for a more gradual incline to 

prevent bigger bikes from dragging bottom. 

10737 

SNOWMOBILE WING KIT

 – Used when lifting snowmobiles 

16355 

CE  FOOT PEDAL

 – Covered foot pedal 

10732 

LIFT DOLLY

 – Helps move lift while in down position 

16010 

TOOL TRAY

 – Keeps tools organized and Handy 

 

 

STANDARD AIR LIFT

Summary of Contents for 10740










Reviews: