background image

                                           

 

 

Under  normal  working  conditions,  the  hydraulic  oil  is  to be  changed  after  2000  operating  hours. 
When changing the oil, drain the oil after the machine has been warmed up. Use oil grade AW46. 

 

4.2.4 

Filter Change 

 

Under normal working conditions, the filter elements (filter cartridges) have to be changed as 
follows:   

 

 - after the first 50 operation hours, then at 1000 hour intervals 

 

Note: Use only original filter elements. 

 

4.2.5 

Regular Control Checks: 

 
 

- Strange noises 

 

 

 

Daily 

 

- Fluid leaks 

 

 

 

 

Daily 

 

- Loose bolts or pins 

 

  

 

Daily 

 

- Pipe, tube or hose leaks 

 

 

Monthly 

 

     (connections, scrubbings, bends) 

Page 19 

 

4.3 

Greasing 

 

Each zerk must be greased every 50 operating hours. Grease is to be applied until it is coming 
out of the greasing point. All greasing points have a red mark. 
Grease recommendation: Multi Purpose EP-2 or equivalent 

 
 

4.4 

Rope Inspection and Replacement 

 

The rope must be replaced if any of the following occur: 

 

a) There are 3 wire breaks within a length of wire equal to the diameter x 6  
b) There are 6 wire breaks within a length of wire equal to the diameter x 30 
c) The rope diameter is reduced by 20% due to flattening 
d) There are significant deformations or bends in the rope 

 
 

4.5 

Drive Chain and Chain Wheels 

 

Drive chains and chain wheels have to be checked every 50 operating hours for wear and damage. 
Furthermore, the chain tension has to be checked and the chains have to be tightened, if necessary. 
Chain sag on the return strand of drives should be approximately 1% of the axle distance or 1/8 to 
1/4 inch in normal position. 
 
 
 
 
 
 
 
 

 

Summary of Contents for KE-SP 3050





























Reviews: