Natrix IOM
TGW Safety Recommendation
For additional safety information: TGW agrees to the following safety instruction or guidelines
listed with the below recommended web site information. This is not to conflict with your state
or legal requirements.
TGW Recommends for maintenance or repair purposes, to incorporate a lock out or tag
procedure. To ensure all starting devices, prime movers, or powered accessories are off before
attempting to maintenance or repair. The procedures below are designed to protect everyone
involved with the conveyor against an unexpected restart. To include understanding of potential
hazard of stored energy, which can exist after the power source is locked out.
For additional information, refer to the latest issue of ANSI Z244.1, American National
Standard for Personnel Protection
− Lockout/Tagout of Energy Sources− Minimum
Safety Requirements.
OSHA 29CRF Part 1910.147
“Control of Hazardous Energy Sources (Lockout/Tagout)”,
which
includes requirements for release of stored energy and OSHA Safety and Health Regulations
for Construction 1926.555 Conveyors
Conveyor Design and Safety Guidelines
A safety risk evaluation is required for all of our standard equipment. The safety risk
evaluation considers every potential hazard on the conveyor, weighs the probability and the
severity of the potential injury, and addresses methods of mitigation to make the risk of injury
either low or negligible. We use the ANSI B11 TR3 standards for all of our risk evaluation.
In addition, all of our equipment is designed to comply with the following national and industry
standards:
CEMA Safety Standards and Labels - (CEMA is the Conveyor Equipment Manufacturers
Association)
ASME B20.1- Safety standard for Conveyors and Related Equipment
ASME B15.1 – Safety standard for Mechanical Power Transmission Apparatus
OSHA 1910.147 – The Control of Hazardous Energy
OSHA 1910.212 - General Requirements for all Machines
OSHA 1910.95 – Occupational Noise Exposure
ANSI 2535 – Safety Color Code
Revision Date: 12/10/2014
Page
9
of
111
Summary of Contents for Natrix
