background image

©Copyright Task Force Tips LLC  2002-2019 

LIX-518 January 23, 2019 Rev12

3

1.0 MEANING OF SAFETY SIGNAL WORDS

A safety related message is identifi ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular 
hazard. Per ANSI standard Z535.4-2007, the defi nitions of the four signal words are as follows:

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious 
injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious 
injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor 
or moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

2.0  SAFETY

The operation of this monitor can be dangerous. The following must be observed at all times.

DANGER

When operating the Extend-A-Gun you may be in a precarious position. Watch your footing on top 
of the truck. It can become very slippery. It is possible to fall off  the truck onto the pavement.

WARNING

The Extend-A-Gun may be used in either the raised or the lowered position, but not in-between. 
Make sure that the slide bar is down and both pawls are fl ush with the housing before use. If the 
word “UNLOCKED” is visible, the Extend-A-Gun is unlocked and may rise suddenly if it is in the 
lowered position and the water is turned on or fall suddenly if it is in the raised position and the 
water is turned off . When the pawls are fl ush with the housing, and the water is turned on, the 
pawls are locked in position and prevent the latch mechanism from operating.

WARNING

Do not plug or cap the Extend-A-Gun or mounted deck gun while it is in the raised position. This 
will prevent the Extend-A-Gun from being lowered all the way and the latch pawls will not lock.

WARNING

For safe dependable service, the Extend-A-Gun must be securely mounted.

WARNING

The forces acting on the mounting brackets, when the Extend-A-Gun is in the extended position, 
are higher than the forces in a normal deck gun installation.

WARNING

Keep the upper and lower brackets as far apart as possible to minimize the amount of stress on 
the upper and lower brackets.

WARNING

Master stream fl ows are very powerful and capable of causing injury and property damage. Make 
sure the monitor is pointing in a safe direction before water to the monitor is turned on. Use care 
in directing the stream.

CAUTION

Do not lift the slide bar when water is fl owing, the mechanism will not unlatch, but the mechanism 
can be damaged.

CAUTION

Do not lift the slide bar to lower the deck gun without supporting the weight of the deck gun. It 
can fall and cause injury.

Summary of Contents for Extend-A-Gun XG18













Reviews: