background image

or abnormality of motor is detected, and contact your vendor or service center 
immediately. 

19. If problem cannot be addressed according to the manual, please close the valves 

on the inlet and outlet of the pump immediately, cut off power supply and contact 
your vendor or service center immediately.

20. This product shall be put in a place out of reach of children. After installation, take 

an isolation measures to avoid access of children. 

21. This product shall be stored in a dry, well ventilated and cool place under room 

temperature. 

Warning

Before installation, you must carefully read the installation 
and operation manual. The installation and use of the 
equipment  must  comply  with  local  regulation  and 
applicable operation standards. 

Warning

Those who have weak physical strength,  react slowly 
or lack experience and knowledge (including children) can 
use this motor pump only under the monitoring and 
direction of his/her safety personnel. 

Caution

Note

Warning

Failure to comply with this safety instruction may lead to 
personal injury!

Failure to comply with this safety instruction may lead to 
equipment malfunction or damage!

Note or instruction for easy and safe operations. 

1. Signs

02

APUMP-HE

Summary of Contents for Tower APUMP-HE Series



















Reviews: