Instruction
Manual
PK
60
UNV
page
15
________________________________________________________________________________________________________________________
The DIN rail cutting dies are equipped with a sheet metal guide
which facilitate a cut in a right angle.
When the cut is completed the retraction is provided by actuating
the retract lever of the pump.
5.1.3 Use of the punch adapter
The advance (penetration) of the punch into the die must be
observed carefully. As soon as the sheet metal is punched the
punching cycle must be terminated by releasing the trigger (Pos.-
No. 1).
Attention
If the punching cycle is not terminated after the sheet
metal is punched the punch will contact the die which
might result in fracture of one or the other.
5.2. Explanation of the application range
The hydraulic tool can be operated with a large number of various
crimping (Chart # 1) and cutting dies (Chart # 2).
Attention
Do only crimp or cut those connecting materials or
conductors according the determined use (for
additional information see our catalog)
If different conducting materials have to be crimped or cut, please
contact the manufacturer.
Attention
Do not crimp on live cables or conductors
5.3. Mounting instructions
Please read the assembly instructions in Chapter 12 of our general
catalogue.
Attention
Even if the code number is identical only those dies
should be used which are suitable for the material.
Please use the following assembly instructions for cable lugs and
connectors:
1. Strip the conductor according to insertion depth (+10% due to the
change of length of the crimped sleeve)
2. The conductor ends must be cleaned with a cloth or brush before the
assembly.
3. Insert the conductor fully into the cable lug or connector
4. Pay attention to the crimping directions and use the appropriate
dies. The crimping directions for cable lugs and connectors is
indicated in the illustration below.
5. After crimping, wipe away excess compound forced out of Al-cable
lugs and connectors.
5.4 Service and maintenance instruction
For every day service the unit has to be cleaned and dried after each
use.
For service cycles please reference the instruction manual of the
pump. The tool must be sent to an authorized service center for
service.
Within the determined use of the tool only the dies and the adapters
are permitted to be changed by the customer.
Instruction
Manual
PK
60
UNV
page
15
_______________________________________________________________________________________________________________________
The DIN rail cutting dies are equipped with a sheet metal guide
which facilitate a cut in a right angle.
When the cut is completed the retraction is provided by actuating
the retract lever of the pump.
5.1.3 Use of the punch adapter
The advance (penetration) of the punch into the die must be
observed carefully. As soon as the sheet metal is punched the
punching cycle must be terminated by releasing the trigger (Pos.-
No. 1).
Attention
If the punching cycle is not terminated after the sheet
metal is punched the punch will contact the die which
might result in fracture of one or the other.
5.2. Explanation of the application range
The hydraulic tool can be operated with a large number of various
crimping (Chart # 1) and cutting dies (Chart # 2).
Attention
Do only crimp or cut those connecting materials or
conductors according the determined use (for
additional information see our catalog)
If different conducting materials have to be crimped or cut, please
contact the manufacturer.
Attention
Do not crimp on live cables or conductors
5.3. Mounting instructions
Please read the assembly instructions in Chapter 12 of our general
catalogue.
Attention
Even if the code number is identical only those dies
should be used which are suitable for the material.
Please use the following assembly instructions for cable lugs and
connectors:
1. Strip the conductor according to insertion depth (+10% due to the
change of length of the crimped sleeve)
2. The conductor ends must be cleaned with a cloth or brush before the
assembly.
3. Insert the conductor fully into the cable lug or connector
4. Pay attention to the crimping directions and use the appropriate
dies. The crimping directions for cable lugs and connectors is
indicated in the illustration below.
5. After crimping, wipe away excess compound forced out of Al-cable
lugs and connectors.
5.4 Service and maintenance instruction
For every day service the unit has to be cleaned and dried after each
use.
For service cycles please reference the instruction manual of the
pump. The tool must be sent to an authorized service center for
service.
Within the determined use of the tool only the dies and the adapters
are permitted to be changed by the customer.
