Textron JACOBSEN GP400 Technical/Repair Manual Download

Page: 297 / 354

CUTTING UNITS

4252490-Rev A

8-25

NOTE

Record the locations of flat washers (7) to ensure correct
installation.

Remove cotter pin (6), pin (5), and six flat washers
(7) from lift cylinder (8) and lift arm (13).

Remove cotter pin (11), pin (12), and two flat
washers (10) from lift cylinder (8) and frame (9).

Move lift cylinder (8) aside.

Figure 8-23

Remove cotter pin (15) and flat washer (16) from lift
arm shaft (14).

Remove lift arm.

Disassembly and Assembly

See Figure 8-24.

Figure 8-24

NOTE

Apply grease that meets or exceeds NLGI Grade 2 LB
specifications to grease fitting (3).

TN3739

Lift Arm

Link Arm

Rubber Bumper

Nut

Grease Fitting

Pivot Shaft

TN3741

Summary of Contents for JACOBSEN GP400



































































































































































































































































































































































Search results

Summary of Contents for JACOBSEN GP400

Reviews:

Related manuals for JACOBSEN GP400

Brands by name

Popular brands

Textron JACOBSEN GP400, Technical/Repair Manual

Search results

Summary of Contents for JACOBSEN GP400

Reviews:

Related manuals for JACOBSEN GP400

Brands by name

Popular brands