background image

EK50ML Battery-powered Crimping Tool

Greenlee / A Textron Company

2

Description

The EK50ML Battery-powered Crimping Tool is a  

hand-held, self-contained crimping tool  intended to  

crimp cable using Greenlee’s Kwik Cycle

®

 9 and 

CrimpALL

®

 die sets as well as some competitors’ 

die sets.
U.S. patent pending.

Safety

Safety is essential in the use and maintenance of  

Greenlee tools and equipment. This manual and any 

markings on the tool provide information for avoiding 

hazards and unsafe practices related to the use of this 

tool. Observe all of the safety information  provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with  

the safe operation and maintenance procedures for the 

following Greenlee tool:
 

EK50ML 

Battery-powered Crimping Tool

Keep this manual available to all personnel.

 

Do not discard this product or throw away!

  

KEEP THIS MANUAL

Table of Contents

Description ..................................................................... 2
Safety ............................................................................. 2
Purpose of this Manual .................................................. 2
Important Safety Information ..................................... 3–4
Identification ................................................................... 5
Specifications ................................................................. 5
Battery Charger .............................................................. 6
Operation .................................................................... 7–8
Maintenance ................................................................... 9
Troubleshooting ............................................................ 10
Die Holders ................................................................... 11
CrimpALL

®

 Interchangeable Die Sets .....................11-13

Illustration ..................................................................... 14
Parts List .................................................................15-16

All specifications are nominal and may change as design 

improvements occur. Greenlee Textron Inc. shall not be liable for 

damages resulting from misapplication or misuse of its products.
CrimpALL and Kwik Cycle are registered trademarks of 

Textron Innovations Inc.
Teflon is a registered trademark of Dupont.

www.calcert.com

[email protected]

1.800.544.2843

0

5

10

15

20

25

30

Summary of Contents for Greenlee EK50ML

















Reviews: