background image

6036 Triple Sheave

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

REPRINTED WITH PERMISSION BY THE CROSBY GROUP

Hook Latch Kit

Warnings and Application Instructions

CAUTION

SEE INSTRUCTIONS

HOOK MUST

 SUPPOR

T LOAD

SS-4055

Important Safety Information – 

Read and Follow

Always inspect hook and latch before using.

• 

Never use a latch that is distorted or bent.

• 

Always make sure spring will force the latch against the tip 

• 

of the hook.
Always make sure hook supports the load. The latch must 

• 

never support the load. (See Figures 1 and 2.)
When placing two (2) sling legs in hook, make sure the angle 

• 

between legs is small enough and the legs are not tilted so 

that nothing bears against the bottom of the latch.  

(See Figures 3 and 4.)
Latches are intended to retain loose sling or devices under 

• 

slack conditions.
Latches are not intended to be an anti-fouling device.

• 

Lo

• 

ads may disengage from hook if proper pro cedures are 

not followed.

A falling load may cause serious injury or death.

• 

See OSHA Rule 1926.550(g)(4)(iv)(B). A hook 

 

• 

and this style latch must not be used for lifting personnel.

Hook must always support the load. The load must never 

• 

be supported by the latch.
Read and understand these instructions before using 

• 

hook.

Right

Wrong

Right

Wrong

  Figure 1    Figure 2     Figure 3        Figure 4

IMPORTANT — Instructions for Assembling SS-4055 Latch on Crosby Hooks

Step 1

Step 2

Step 3

Steps 4, 5, and 6

Place hook at approximately 

a 45-degree angle with the 

cam up.

Position coils of spring over 

cam with tines of spring 

pointing toward point of hook 

and loop of spring positioned 

down and lying against the 

hook.

Position latch over tines of 

spring with ears partially over 

hook cam. Swing latch to 

one side of hook, point and 

depress latch and spring until 

latch clears point of hook.

4.  Line up holes in latch with 

hook cam.

5.  Insert bolt through latch, 

spring, and cam.

6.  Tighten self-locking nut on 

one end of bolt.

Summary of Contents for GREENLEE 6036













Reviews: