3
Instruction Manual Cutting Tool
GB
authorised
copy
The tool is not designed for continued cutting operations.
After a sequence of approximately 30-40 completed cuts
you have to make a break of 15 min. to give the tool time
to cool down.
Attention
Too intensive use can cause heat damages for
the tool
Attention
During the operation of electric engines sparks
can occur which might ignite highly infl ammab-
le or explosive liquids and materials
Attention
Electric-hydraulic tools should not be operated
in pouring rain or under water.
4.3 Service and maintenance instruction
For every day service the tool has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
Attention
Maintain power tools thoroughly. Check for
functionality or jamming of moving parts, brea-
kage of parts and any other condition that may
affect the power tools operation.
The electric-hydraulic unit is equipped with a controller
enabling the user to see when the next service is due by
fl
ashing for 20 sec. at the end of a working cycle. When
the next service is due after 10.000 cycles the unit must
be returned to an authorised service center (ASC). Failu-
re to observe this request results in loosing the Warranty.
Preventive maintenance serves your safety. Within the
determined use of the tool only the blades are permitted
to be changed by the customers.
Attention
Do not damage the seals of the tool
Attention
Have the power tool repaired by a qualifi ed ex-
pert or by a Klauke ASC before use.
Attention
Keep the blades clean and grease the guidance
regularly.
5. Troubleshooting
a.) Constant
fl
ashing/indicating of the light diode display
(page I, pic 1, 1) .
see table 1. If the failure can not be solved through
the action recommended in table 1 return the tool to
the nearest service center (ASC).
b.) The tool loses oil.
Return the unit to the manufacturer. Do not open it
and damage the seal of the tool.
HE.13457_B © 09/2010
ESG 50-L
6. Technical Data
Weight
(incl. battery):
approx. 4,7 kg
Cutting force:
approx. 60 kN
Maximum
cutting diameter:
Ø 50 mm
Driving motor:
direct-current permanent
fi
eld
Battery voltage:
18 V DC
Battery capacity:
3 Ah (RAL2/BL1830)
Charging time:
22 min. (RAL2/BL1830)
Cutting time:
approx. 8 s to 18 s
(depending on the connector size)
Cuts per battery
charge:
approx. 140 cuts
(4x120 mm² NYY)
Hydraulic oil:
Rivolta S.B.H. 11
Environmental
temperature:
-12°C bis +40°C
Sound level:
< 70 dB (A) in 1m distance
Vibrations:
< 2,5 m/s²
Dimensions:
See pic. 2
7. Putting out of operation/waste dis-
posal
This unit is subjected to the scope of the European WEEE
(2002/96/EG) and RoHS (2002/95/EEC) directives.
Information about this can be found in our home page
www.Klauke.com under ‘WEEE & RoHS’.
Battery cartridges must be specially disposed of accor-
ding to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmental friendly.
Kontaktadresse:
[email protected]
Attention
Additional instruction manuals are available
free of charge. The part # is HE.13457.
The In-
struction Manual can also be downloaded from
our Homepage www.klauke.textron.com.
