Textron 783310003731, Operation Manual

Page: 7 / 25

HW1 and HW1V Impact Wrenches
Greenlee / A Textron Company
Specifications
Impact Wrench
5ZQFPG)ZESBVMJD4ZTUFN ............................. 0QFODFOUFS
PSDMPTFEDFOUFS
Hydraulic Pressure Port ... m6/'4"&0SJOH#PTT
Hydraulic Return Port ........
m6/'4"&0SJOH#PTT
0VUQVU!MNJO HQN
31. OPMPBE
...................................................... 6500
*NQBDUTQFS.JOVUF OPMPBE ...............................
Torque ..................................................
/N GUMC
%SJWF4J[F .........................................1/2" square drive w/
IFYRVJDLDIBOHFDIVDL
7JCSBUJPO-FWFM ...................................................... 11 m/s 2
/PJTF-FWFM
..........................................................
-XB
Mass/Weight
HW1 .......................................................
LH MC
HW1V ..................................................... LH MC
-FOHUI
........................................................
NN
Width .......................................................... NN
Height .......................................................
NN
Hydraulic Power Source
Do not exceed the following hydraulic power source
NBYJNVNT
r )ZESBVMJDáPX MNJO HQN
r 1SFTTVSFSFMJFG CBS QTJ
r #BDLQSFTTVSF CBS QTJ
Failure to observe this warning could result in severe
injury or death.
5ZQFPG)ZESBVMJD4ZTUFN ............................. 0QFODFOUFS
PSDMPTFEDFOUFS
Flow
Minimum .........................................
MNJO HQN
Recommended ............. UPMNJO UPHQN
Maximum .........................................
MNJO HQN
Filtration ............................................. .JDSPO OPNJOBM
1SFTTVSF3FMJFG4FUUJOH
........................
CBS QTJ
#BDL1SFTTVSF NBYJNVN .................. CBS QTJ
CBS QTJJTUIFNBYJNVNBHSFFETUBOEBSECBDLQSFTTVSF
GPSUIF)5." )ZESBVMJD5PPM.BOVGBDUVSFST"TTPDJBUJPO
(SFFOMFF6UJMJUZUPPMXJMMPQFSBUFTBUJTGBDUPSJMZBUUIJTTUBOEBSE
1. Maximum hydraulic fluid temperature must not
FYDFFEž$ ž'"TVGàDJFOUPJMDPPMJOH
capacity is needed to limit the hydraulic fluid
temperature.
)ZESBVMJDáPXNVTUOPUFYDFFEMNJO HQN
Install a flow meter in the return line to measure the
rate of hydraulic flow before using the tool.
1SFTTVSFSFMJFGWBMWFTFUUJOHNVTUOPUFYDFFE
CBS QTJBUZPVSUPPMTNBYJNVNáPX
-PDBUFUIFQSFTTVSFSFMJFGWBMWFJOUIFTVQQMZDJSDVJU
to limit excessive hydraulic pressure to the tool.
Hydraulic Schematic
FILTER
(10 MICRON)
COOLER
RELIEF
VALVE
138 bar
(2000 psi)
CONTROL
VALVE
FLOW METER
T
P
TOOL
RESERVOIR
PUMP
POWER SOURCE
Recommended Hydraulic Fluids
6TFBOZOPOEFUFSHFOUQFUSPMFVNCBTFEIZESBVMJD
áVJEXIJDINFFUTUIFGPMMPXJOHTQFDJàDBUJPOTPS)5."
TQFDJàDBUJPOT
464!
ž$ ž'
.............................................. 140 to 225
ž$ ž' ........................................... 40 minimum
Flash Point ................................
ž$ ž'NJOJNVN
Pour Point .................................. ž$ ž'NJOJNVN
Hydraulic Power Source DPOUE
www. .com
information@itm.com 1.800.561.8187