OPERATION AND SERVICE INFORMATION
Page 17
Owner’s Manual and Service Guide
Read all of Manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Dangers and Warnings
Fig. 19 Inspect Oil Filter
Be careful of hot oil when drained. It may be hot
enough to burn you severely
Drain the oil by removing the drain plug found at the rear
of the engine base. Remove using a 3/4" wrench. At the
first oil change,
small
metal chips and lint may be found.
This is normal, resulting from the break-in period. Inspect
the filter at every oil change. The presence of large metal
chips could indicate possible damage to the engine.
Fig. 20 Oil Drain Plug
Wipe the area around the drain plug mount with a lint
free cloth and inspect the drain plug (A) for damage;
replace if necessary. Replace the "O"-ring (B) with a new
one and tighten to 61 in. lbs. (7.0 Nm) torque.
Apply engine oil to the oil filter seal and install oil filter
onto the engine until the seal contacts mounting surface
of the engine. Then turn the filter 2/3 to 3/4 rotations by
HAND(S). Pour in the specified type and amount of oil
See "Capacities and Replacement Parts" on page 23.
Oil capacity is 1 1/3 quarts (1.3 liters). Add slightly less
than 1 1/3 quarts (1.3 liters) to allow for possible residual
oil left in engine. The oil must be high quality oil that
meets or exceeds API SF, SG, CC standards (Ref Fig. 21
on page - 17). Check oil level on dipstick. Oil should be
slightly below ‘H’ to allow for expansion. If necessary,
continue to add oil slowly and allow time for oil to flow
down into engine. Check oil level on dipstick.
Do not
overfill.
Do not overfill engine. Too much oil may cause smoking
or allow oil to enter the air filter enclosure.
Fig. 21 Add Engine Oil
Both the oil dipstick and fill cap must be in place before operat-
ing the engine. Failure to install the dipstick and fill cap will
result in oil being discharged into the engine compartment.
As a final check, check the oil level again with the vehicle
on level ground. Like all liquids, oil increases in volume
when warm. The full ‘H’ mark on the dipstick is calibrated
for an engine at operating temperature. When the engine
is cold, the oil will be below the full mark. The engine can
be operated safely as long as the oil is within the safe
operating range as indicated on the dipstick.
Do not
operate vehicle if oil level is below the safe area indi-
cated on the dipstick.
STARTER/GENERATOR BELT TENSION
Tool List
Qty. Required
Belt tension gauge....................................................... 1
Wrench, 3/4"................................................................ 1
Wrench, 9/16".............................................................. 2
Ratchet, 3/8" drive ....................................................... 1
Socket, 3/4", 3/8" drive ................................................ 1
NOTICE
Summary of Contents for 614212 2010
