background image

 
 
 

17 

 

 

 

 

 

 

 

 

Warning:

 Never refill oil over the higher end of the interval, this will damage the engine. 

 
Engine oil change  

Drain the old / staled oil while the engine is warm. Warm oil is more fluid then cold and drains 

better. 

 

How to: 

  Place a suitable container below the engine to catch the used oil. 

  Remove the filler cap and the drain plug.  

  Drain completely! 

  Reattach the drain plug, and tighten it securely.  

  Refill new recommended oil. 

 

 

 

 

Please dispose the used engine oil environmentally correct. We suggest that you keep the used oil 

in a sealed container and dispose at your recycling center or service station for reclamation. Do not 

throw it in the waste; pour it on the ground; or down a drain.  

 

Engine oil specifications  

Oil is affecting the performance of your machine and service life. Use 4-stroke automotive 

detergent oil.  

 

SAE 10W-30 is recommended for general use. The SA oil viscosity and service classification are in 

the API label on the oil container. We recommend that you use API SERVICE Category SE or SF 

oil. 

 

 

 

 

 

 

 

The snowbuster 1100E has engine oil capacity of 1.1 Liter 

 

Spark Plug  

Check the spark plug for dirt and grime; if necessary clean it with a copper wire brush.   

  first time after approximately 10 hours of operation  

  Thereafter service the spark plug after every 50 hours of operation. 

How to:

 

  Disconnect the spark plug cap, and remove any dirt from around the spark plug area. 

  Remove the spark plug with a spark plug wrench. Inspect the spark plug. 

  Replace it if the electrodes are worn, or if the insulator is cracked or chipped.  

  Measure the spark plug electrode gap with a suitable gauge.  

Summary of Contents for Snowbuster 1100E























Reviews: