manualshive.com logo in svg

Texas Weather Instruments Weather Report WR-25, Instruction Manual

Share
Download
Texas Weather Instruments Weather Report WR-25 Instruction Manual Download Page 20

Texas Weather Instruments, Inc.                         

20

  

                        

WR-25 Instruction Manual

the windspeed output to the RS-232 port is an instant reading rather than a one minute
average.

To turn on the desired control options via the weather station display, refer to the table
below, add up the values of the controls that should be turned on and enter that value
into the weather instrument via the print set function (see page 13).  The default value is
224.  For example if you wanted AM PM turned on and instant wind speed output
turned on you would add 32+128 which equals 192.  Enter 192 into the weather
instrument via the print set function.

Option

Value

Knots on

16

AM PM on

32

Aux disable on

64

Instant wind speed on

128

   total

You may also change these functions via the software program TWI_LOG F5 routine

RS-232  Interface

RS-232  Interface

The pin out on the RS-232interface is as follows:

.

DE 9 Plug

Header

Pin 1

Pin 1 . . . 

Pin 2

Pin 3 . . . 

Receive Data

Pin 3

Pin 5 . . . 

Transmit Data

Pin 4

Pin 7 . . . .

Data Set Ready

Pin 5

Pin 9 . . .

Signal Ground

Pin 6

Pin 2 . . .

Data Terminal Ready (must be true to send data)

Pin 7

Pin 4 . . .

Clear to Send

Pin 8

Pin 6 . . .

Request Send

Pin 9

Pin 8 . . .

Modem Installation

A modem may be used with the WR-25 for remote operations.  A modem
adapter which is available from TWI must be used to properly connect the
weather station to a modem.  For auto answering, an auto-answering modem
with non-volatile memory must be used.  The WR-25 does not send AT control
signals, so in order for the modem to properly answer, the modem must be told
(programmed with a computer) to answer on whichever ring the user desires.

Summary of Contents for Weather Report WR-25






























Reviews:

No comments

Brands by name

Popular brands

Load more brands