background image

WD Response WINDOW 1

Programmed through the WDT_WIN1_CFG register 

(0.55 ms to 140.8 ms in 0.55-ms steps)

WD Response WINDOW 2

Programmed through the WDT_WIN2_CFG register 

(0.55 ms to 17.6 ms in 0.55-ms steps)

Three correct SPI WD question responses must be scheduled in this interval, in the correct 
order:

After the t

WD_RESP_WIN1

 time elapses, the WD response WINDOW 2 begins.

Responses (

answers

) are written to the WDT_ANSWER register.

The SPI WD question- response sequence order is important.

The final correct SPI-WD question response 
(WD_ANSWER_RESP_0) must be scheduled in this time 
interval.

After the last correct SPI-WD answer response, the next 
WD question is generated within 1 system clock cycle 
(typically 125 ns), after which the next WD response 
WINDOW 1 (Q&A+1) starts

WD_ANSWER_

RESP_3

WD_ANSWER_

RESP_2

WD_ANSWER_

RESP_1

WD_ANSWER_

RESP_0

SPI WD Question Sequence Responses

(2)

WD Question Response Sequence

WD  Question 

Request

RD_WD_

QUESTION

SPI Question 

Required

(1)

SPI 

Commands

NCS pin

1 internal system clock cycle (125 ns)

to generate a new WD question for Q&A+1

Q&A [n]

Q&A [n + 1]

t

WD_RESP_WIN1

 + t

WD_RESP_WIN2

x

WD_ANSWER_RESP_3

x

WD_ANSWER_RESP_2

x

WD_ANSWER_RESP_1

Answer0 to 

Question

Question to

Answer3

Answer3 to

Answer2

Answer2 to

Answer1

Answer1 to

Answer0

WINDOW 1 Duration

WINDOW 2 Duration

www.ti.com

TPS65313 GUI

9

SLDU028A – January 2018 – Revised March 2020

Submit Documentation Feedback

Copyright © 2018–2020, Texas Instruments Incorporated

TPS65313-EVM User’s Guide

Figure 5. Watchdog Window Timing Diagram

Section 11

describes the watchdog implementation on the MSP430™ MCU on the EVM.

6.1.7

MCU Error Signal Monitor (ESM)

The MCU error monitoring function is implemented in the GUI to check the functionality of MCU_ERR pin.
Both PWM mode and TMS570 mode of error monitoring is implemented on the GUI. Each setting is
described as follows:

TMS570 Mode button —

This option reads the register values and populates the corresponding text field

with the corresponding low and high periods.

Write MCU Error Window Registers button —

When enabled, the timing thresholds set in the text field

are written to the corresponding device timing registers (PWM_LMAX, PWM_LMIN, PWM_HMAX,
PWM_HMIN).

Enable PWM Output button —

The

Low Duration

,

High Duration

, and the

Enable PWM Output

options

turn on the clock with those periods on the MCU GPIO connected to the MCU_ERR pin. Jumper
J11 must be set between pin 2 and pin 3 for this signal to be applied to the device pin.

MCU Error Window Register Values fields —

This option reads the timing register values and

populates the corresponding text field with the corresponding low and high periods.

The ESM is disabled by default, and can be activated by setting the MCU_ESM_EN bit to 1b in the
SAFETY_CHECK_CTRL SPI register.

6.1.8

SPI Status Bits

The SPI status flag response byte of the device is displayed in this section of the

Device Controls

page.

For more information, refer to the

TPS65313-Q1 Wide-VIN Power-Management IC for Automotive

Applications

datasheet.

Summary of Contents for TPS65313-EVM











































Reviews: