background image

2 Test Setup and Results

This section describes how to properly connect, set up, and use the TPS54331EVM-232 and evaluation 
modules. The section also includes test results typical for the evaluation modules and covers efficiency, output 
voltage regulation, load transients, loop response, output ripple, input ripple, and start-up.

2.1 Input / Output Connections

The TPS54331EVM-232 is provided with input/output connectors and test points as shown in 

Table 2-1

. A power 

supply capable of supplying 3 A must be connected to J1 through a pair of 20 AWG wires. The load must 
be connected to J4 through a pair of 20 AWG wires. The maximum load current capability must be 3 A. Wire 
lengths must be minimized to reduce losses in the wires. Test-point TP1 provides a place to monitor the VIN 
input voltages with TP2 providing a convenient ground reference. TP5 is used to monitor the output voltage with 
TP6 as the ground reference.

Table 2-1. EVM Connectors and Test Points

REFERENCE 

DESIGNATOR

FUNCTION

J1

VIN (see 

Table 1-1

 for VIN range)

J2

2-pin header for enable. Connect EN to ground to disable, open to enable.

J3

2-pin header for slow start monitor and GND.

J4

VOUT, 3.3 V at 3-A maximum

TP1

VIN test point at VIN connector

TP2

GND test point at VIN

TP3

PH test point

TP4

Test point between voltage divider network and R3. Used for loop response measurements.

TP5

Output voltage test point at OUT connector

TP6

GND test point at OUT connector

2.2 Efficiency

The efficiency of this EVM peaks at a load current of about 0.6 A - 1 A and then decreases as the load 
current increases towards full load. 

Figure 2-1

 shows the efficiency for the TPS54331EVM-232 at an ambient 

temperature of 25°C.

0

10

20

30

40

50

60

70

80

90

100

0

0.5

1

1.5

2

2.5

3

I

- Output Current - A

O

Efficiency-%

V

= 7 V

IN

V

= 14 V

IN

V

= 21 V

IN

V

= 28 V

IN

Figure 2-1. TPS54331 Efficiency

Test Setup and Results

www.ti.com

4

TPS54331 Step-Down Converter Evaluation Module User's Guide

SLVU247A – JULY 2008 – REVISED OCTOBER 2021

Submit Document Feedback

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for TPS54331




















Reviews: