Texas Instruments TMS570LC4357, Technical Reference Manual

Page: 838 / 2208

EMIF Registers
www.ti.com
838 SPNU563A – March 2018
Submit Documentation Feedback
Copyright © 2018, Texas Instruments Incorporated
External Memory Interface (EMIF)
21.3.11 EMIF Interrupt Mask Clear Register (INTMSKCLR)
The EMIF interrupt mask clear register (INTMSKCLR) is used to disable the Asynchronous Timeout
Interrupt. If read as 1, the AT_MASKED bit in the EMIF interrupt masked register (INTMSK) will be set and
an interrupt will be generated when an Asynchronous Timeout occurs. If read as 0, the AT_MASKED bit
will always read 0 and no interrupt will be generated when an Asynchronous Timeout occurs. Writing a 1
to the AT_MASK_CLR bit disables the Asynchronous Timeout Interrupt. The EMIF on some devices does
not have the EMIF_nWAIT pin, therefore, these registers and fields are reserved on those devices. The
INTMSKCLR is shown in
Figure 21-25 and described in Table 21-35 .
Figure 21-25. EMIF Interrupt Mask Clear Register (INTMSKCLR) [offset = 4Ch]
31 16
Reserved
R-0
15 3 2 1 0
Reserved WR_MASK_CLR LT_MASK_CLR AT_MASK_CLR
R-0 R/W-0 R/W-0 R/W-0
LEGEND: R/W = Read/Write; R = Read only; - n = value after reset
Table 21-35. EMIF Interrupt Mask Clear Register (INTMSKCLR) Field Descriptions
Bit Field Value Description
31-3 Reserved 0 Reserved. The reserved bit location is always read as 0. If writing to this field, always write the
default value of 0.
2 WR_MASK_CLR Wait Rise Mask Clear. This bit determines whether or not the wait rise interrupt is enabled. Writing
a 1 to this bit clears this bit, clears the WR_MASK_SET bit in the EMIF interrupt mask set register
(INTMSKSET), and disables the wait rise interrupt. To set this bit, a 1 must be written to the
WR_MASK_SET bit in INTMSKSET.
0 Indicates that the wait rise interrupt is disabled. Writing a 0 has no effect.
1 Indicates that the wait rise interrupt is enabled. Writing a 1 clears this bit and the WR_MASK_SET
bit in the EMIF interrupt mask set register (INTMSKSET).
1 LT_MASK_CLR Line trap Mask Clear. This bit determines whether or not the line trap interrupt is enabled. Writing a
1 to this bit clears this bit, clears the LT_MASK_SET bit in the EMIF interrupt mask set register
(INTMSKSET), and disables the line trap interrupt. To set this bit, a 1 must be written to the
LT_MASK_SET bit in INTMSKSET.
0 Indicates that the line trap interrupt is disabled. Writing a 0 has no effect.
1 Indicates that the line trap interrupt is enabled. Writing a 1 clears this bit and the LT_MASK_SET bit
in the EMIF interrupt mask set register (INTMSKSET).
0 AT_MASK_CLR Asynchronous Timeout Mask Clear. This bit determines whether or not the Asynchronous Timeout
Interrupt is enabled. Writing a 1 to this bit clears this bit, clears the AT_MASK_SET bit in the EMIF
interrupt mask set register (INTMSKSET), and disables the Asynchronous Timeout Interrupt. To set
this bit, a 1 must be written to the AT_MASK_SET bit of the EMIF interrupt mask set register
(INTMSKSET).
0 Indicates that the Asynchronous Timeout Interrupt is disabled. Writing a 0 has no effect.
1 Indicates that the Asynchronous Timeout Interrupt is enabled. Writing a 1 clears this bit and the
AT_MASK_SET bit in the EMIF interrupt mask set register (INTMSKSET).