Texas Instruments TMS320DM357 User Manual Download Page 107 | Manualshive

Page: 107 / 167

background image

4.3.2.5

EDMA3CC Error Register (CCERR)

www.ti.com

EDMA3 Channel Controller Control Registers

The EDMA3CC error register (CCERR) indicates whether or not at any instant of time the number of
events queued up in any of the event queues exceeds or equals the threshold/watermark value that is set
in the queue watermark threshold register (QWMTHRA). Additionally, CCERR also indicates if when the
number of outstanding TRs that have been programmed to return transfer completion code (TRs which
have the TCINTEN or TCCHEN bit in OPT set to 1) to the EDMA3CC has exceeded the maximum
allowed value of 63. If any bit in CCERR is set (and all errors, including bits in other error registers
(EMR/EMRH, QEMR) were previously cleared), the EDMA3CC generates an error interrupt. Refer to

for details on EDMA3CC error interrupt generation. Once the error bits are set in CCERR,

they can only be cleared by writing to the corresponding bits in the EDMA3CC error clear register
(CCERRCLR).

The CCERR is shown in

and described in

.

Figure 4-21. EDMA3CC Error Register (CCERR)

31

17

16

Reserved

TCCERR

R-0

R-0

15

2

1

0

Reserved

QTHRXCD1

QTHRXCD0

R-0

R-0

R-0

LEGEND: R = Read only; -

n

= value after reset

Table 4-24. EDMA3CC Error Register (CCERR) Field Descriptions

Bit

Field

Value

Description

31-17

Reserved

0

Reserved

16

TCCERR

Transfer completion code error. TCCERR is cleared by writing a 1 to the corresponding bit in the
EDMA3CC error clear register (CCERRCLR).

0

Total number of allowed TCCs outstanding has not been reached.

1

Total number of allowed TCCs has been reached.

15-2

Reserved

0

Reserved

1

QTHRXCD1

Queue threshold error for queue 1. QTHRXCD1 is cleared by writing a 1 to the corresponding bit in the
EDMA3CC error clear register (CCERRCLR).

0

Watermark/threshold has not been exceeded.

1

Watermark/threshold has been exceeded.

0

QTHRXCD0

Queue threshold error for queue 0. QTHRXCD0 is cleared by writing a 1 to the corresponding bit in the
EDMA3CC error clear register (CCERRCLR).

0

Watermark/threshold has not been exceeded.

1

Watermark/threshold has been exceeded.

SPRUG34 – November 2008

Registers

107

Submit Documentation Feedback

«
...
105
106
107
108
109
...
»

Summary of Contents for TMS320DM357








































































































































































Reviews:

No comments

Related manuals for TMS320DM357

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: CAME Pages: 4

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 5

MICROCOMPUTER MN103S

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

WJMPU955 - PROCESSING UNIT - TMU

Brand: Panasonic Pages: 62

Brand: Cypress Semiconductor Pages: 11

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Kontron CP3005 Series

Brand: S&T Pages: 115

Braswell Series

Brand: Intel Pages: 54

Brand: Infoblox Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands