manualshive.com logo in svg

Texas Instruments TMS320C6201, Reference Manual

The Texas Instruments TMS320C6201 is a highly efficient digital signal processor. Ensure smooth functioning of your device by staying updated with the latest Errata Corrections. Download the comprehensive user manual for free from manualshive.com, providing step-by-step instructions, troubleshooting tips, and optimization techniques essential for harnessing the full potential of this powerful product.

Share
Download
background image

Data Transmission and Reception

 

11-18

11.3 Data Transmission and Reception

As shown in Figure 11–1 on page 11-3, the receive operation is triple-buff-
ered and the transmit operation is double-buffered. Receive data arrives on
the DR and is shifted into the RSR. Once a full element (8, 12, 16, 20, 24, or
32 bits) is received, the RSR is copied to the receive buffer register (RBR) only
if the RBR is not full. The RBR is then copied to the DRR unless the DRR has
not been read by the CPU or the DMA controller.

Transmit data is written by the CPU or the DMA controller to the DXR. If there
is no data in the XSR, the value in the DXR is copied to the XSR. Otherwise,
the DXR is copied to the XSR when the last bit of data is shifted out on the DX.
After transmit frame synchronization, the XSR begins shifting out the transmit
data on the DX.

11.3.1 Resetting the Serial Port: (R/X)RST, GRST, and RESET

The serial port can be reset in the following two ways:

-

Device reset (RESET pin is low) places the receiver, the transmitter, and
the sample rate generator in reset. When the device reset is removed
(RESET = 1), FRST = GRST = RRST = XRST = 0, keeping the entire serial
port in the reset state.

-

The serial port transmitter and receiver can be independently reset by the
XRST and RRST bits in the SPCR. The sample rate generator is reset by
the GRST bit in the SPCR.

Table 11–8 shows the state of the McBSP pins when the serial port is reset by
these methods.

Summary of Contents for TMS320C6201






























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C6201

Datasat AP20 Installation And Operating Manual preview
AP20
Brand: Datasat Pages: 32
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Brand: Opvimus Pages: 12
Rolls HR11C Owner'S Manual preview
HR11C
Brand: Rolls Pages: 2
vPipes Uilleann Quick Start Manual preview
Uilleann
Brand: vPipes Pages: 3
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
Idis DR-1508P Operation Manual preview
DR-1508P
Brand: Idis Pages: 85
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
SeaLevel 7205e User Manual preview
7205e
Brand: SeaLevel Pages: 34
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
Bose PowerMatch ESPLink Quick Start Manual preview
PowerMatch ESPLink
Brand: Bose Pages: 2
Neousys Technology PCIe-USB381F User Manual preview
PCIe-USB381F
Brand: Neousys Technology Pages: 24
ZALMAN CNPS20X User Manual preview
CNPS20X
Brand: ZALMAN Pages: 20
Xcellon DRD-501 User Manual preview
DRD-501
Brand: Xcellon Pages: 24

Brands by name

Popular brands

Load more brands