Texas Instruments TDA4VM User Manual Download Page 1

Page: 1 / 84

User’s Guide

Jacinto7 J721E/DRA829/TDA4VM Evaluation Module
(EVM)

ABSTRACT

This technical user's guide describes the hardware architecture and configuration options of the J721E/DRA929/
TDA4VM EVM.

Table of Contents

1 Introduction

.............................................................................................................................................................................

1.1 Key Features......................................................................................................................................................................

1.2 Thermal Compliance..........................................................................................................................................................

1.3 REACH Compliance...........................................................................................................................................................

1.4 EMC, EMI, and ESD Compliance......................................................................................................................................

2 J721E EVM Overview

..............................................................................................................................................................

2.1 J721E EVM Board Identification........................................................................................................................................

2.2 J721E SOM Component Identification...............................................................................................................................

2.3 Jacinto7 Common Processor Components Identification................................................................................................

2.4 Quad Ethernet Components Identification........................................................................................................................

3 EVM User Setup/Configuration

............................................................................................................................................

3.1 Power Requirements........................................................................................................................................................

3.2 Power ON Switch and Power LEDs.................................................................................................................................

3.3 EVM Reset/Interrupt Push Buttons..................................................................................................................................

3.4 EVM DIP Switches...........................................................................................................................................................

3.5 EVM UART/COM Port Mapping.......................................................................................................................................

3.6 JTAG Emulation...............................................................................................................................................................

4 J721E EVM Hardware Architecture

.....................................................................................................................................

4.1 J721E EVM Hardware Top level Diagram........................................................................................................................

4.2 J721E EVM Interface Mapping........................................................................................................................................

4.3 I2C Address Mapping.......................................................................................................................................................

4.4 GPIO Mapping.................................................................................................................................................................

4.5 Power Supply...................................................................................................................................................................

4.6 Reset................................................................................................................................................................................

4.7 Clock................................................................................................................................................................................

4.8 Memory Interfaces...........................................................................................................................................................

4.9 MCU Ethernet Interface...................................................................................................................................................

4.10 QSGMII Ethernet Interface.............................................................................................................................................

4.11 PCIe Interface.................................................................................................................................................................

4.12 USB Interface.................................................................................................................................................................

4.13 CAN Interface.................................................................................................................................................................

4.14 FPD Interface (Audio Deserializer)................................................................................................................................

4.15 FPD Panel Interface (DSI Video Serializer)...................................................................................................................

4.16 Display Serial Interface (DSI) FPC.................................................................................................................................

4.17 Audio Interface...............................................................................................................................................................

4.18 Display Port Interface.....................................................................................................................................................

4.19 MLB Interface.................................................................................................................................................................

4.20 I3C Interface...................................................................................................................................................................

4.21 ADC Interface.................................................................................................................................................................

4.22 RTC Interface.................................................................................................................................................................

4.23 Apple Authentication Header.........................................................................................................................................

4.24 EVM Expansion Connectors..........................................................................................................................................

4.25 ENET Expansion Connector..........................................................................................................................................

www.ti.com

Table of Contents

SPRUIS4D – MAY 2020 – REVISED MARCH 2022

Submit Document Feedback

Jacinto7 J721E/DRA829/TDA4VM Evaluation Module (EVM)

Summary of Contents for TDA4VM





















































































Search results

Summary of Contents for TDA4VM

Reviews:

Related manuals for TDA4VM

Brands by name

Popular brands

Texas Instruments TDA4VM, User Manual

Search results

Summary of Contents for TDA4VM

Reviews:

Related manuals for TDA4VM

Brands by name

Popular brands