Home
/
Texas Instruments
/
OMAP36 Series
/
Technical Reference Manual

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 745 / 3738

Share

Page: 745 / 3738

Texas Instruments OMAP36 Series Technical Reference Manual Download Page 745

Public Version

www.ti.com

IVA2.2 Subsystem Basic Programming Model

5.4.1.1.1 IDLE Boot Mode

In this boot mode the

register is configured before the IDLE instruction is executed. When the

IDLE instruction is executed, if there are no pending requests from either the DMA or an interrupt, IVA
goes into sleep mode.

The

register is programmed as shown in

.

Table 5-10. PDCCMD Programmed Value in IDLE Boot Mode

BitField

Value

Description

GEMPD

1

Sleep mode. Power-down DSP CPU and megamodule when DSP CPU enters
IDLE state.

EMCMEM

11

Internal RAMs sleep with retention.

EMCLOG

11

Maximum dynamic clock gating of module regions, with potential :
latencies/penalties for wake when megamodule is active and Static clock gating to
the EMC when megamodule is in standby.

UMCMEM

11

Sleep mode 3. Internal RAMs sleep with retention, L2 defined at chip-level.

UMCLOG

11

Maximum dynamic clock gating of module regions, with potential
latencies/penalties for wake when megamodule is active and Static clock gating to
the UMC when megamodule is in standby.

DMCMEM

11

Sleep mode 3. Internal RAMs sleep with retention, L1D defined at chip-level.

DMCLOG

11

Maximum dynamic clock gating of module regions, with potential
latencies/penalties for wake when megamodule is active and Static clock gating to
the DMC when megamodule is in standby

PMCMEM

11

Sleep mode 3. Internal RAMs sleep with retention, L1P defined at chip-level.

PMCLOG

11

Maximum dynamic clock gating of module regions, with potential
latencies/penalties for wake when megamodule is active and Static clock gating to
the PMC when megamodule is in standby

5.4.1.1.2 Wait in Self-Loop Mode

In this mode boot loader puts the IVA2 in a self-loop. The MPU then has the option to download the
bootstrap code from the MPU side directly into IVA2 internal memory through host port interface (L3 slave
interface). MPU then sets up CONTROL.CONTROL_IVA2_BOOTMOD[3:0] BOOTMODE to 0 and
CONTROL.CONTROL_IVA2_BOOTADDR[31:10] BOOTLOADADDR to the internal memory address
where it copied the bootstrap, IVA2.2 is then released from reset. When the reset sequence completes,
IVA2.2 jumps to the bootstrap code loaded by the user in its internal memory and starts executing it.

5.4.1.1.3 Default Config Cache Mode

In this mode the boot loader configures the L1P, L1D, L2 caches and the MAR registers of DSP
megamodule. After performing this configuration the boot loader branches to an external memory address.
The values with which these settings are done and the external memory address to which the boot loader
jumps is specified using a header.

specifies the format of the header.

Table 5-11. Header Format Used in Defautl Config Cache Mode

Offset from Base Address of

Fields Description

Header (in bytes)

0x00

Value of

register to be loaded.

0x04

Value of

register to be loaded.

0x08

Value of

register to be loaded.

0x0C

1 -> Set PC bit of all

registers to 1

0 -> No action will be taken as by default PC bit of all

registers is set to 0

0x10

Address of external memory to which boot loader should branch to.

745

SWPU177N – December 2009 – Revised November 2010

IVA2.2 Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
743
744
745
746
747
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments