Texas Instruments OMAP36 Series Technical Reference Manual Download Page 3353

Page: 3353 / 3738

Public Version

www.ti.com

High-Speed USB Host Subsystem

Bits

Field Name

Description

Type

Reset

4:0

RESERVED

Reserved

0x00

Table 22-231. Register Call Summary for Register ASYNCLISTADDR

High-Speed USB Host Subsystem

•

High-Speed USB Host Subsystem Register Summary

[0]

•

High-Speed USB Host Subsystem Register Description

[1]

Table 22-232. CONFIGFLAG

Address Offset

0x0000 0050

Physical Address

0x4806 4850

Instance

EHCI

Description

Configured flag register

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

RESERVED

Bits

Field Name

Description

Type

Reset

31:1

RESERVED

Reserved

0x00000000

Configure Flag

This bit controls the default port-routing control logic.

0x0: Port routing control logic default-routes each port to
an implementation dependent classic host controller.

0x1: Port routing control logic default-routes all ports to
this host controller.

Table 22-233. Register Call Summary for Register CONFIGFLAG

High-Speed USB Host Subsystem

•

High-Speed USB Host Subsystem Register Summary

[0]

•

High-Speed USB Host Subsystem Register Description

[1] [2]

Table 22-234. PORTSC_i

Address Offset

0x0000 0054 + (0x04 * i)

Index

i = 0 to 2

Physical Address

0x4806 4854 + (0x04 * i)

Instance

EHCI

Description

Port Status/Control

Type

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

RESERVED

PTC

PIC

FPR

SUS

PED

CSC

CCS

WDE

WCE

PEDC

RESERVED

Bits

Field Name

Description

Type

Reset

31:22

RESERVED

Reserved

0x000

WDE

Wake on Disconnect Enable

This field is 0 if the PP bit is 0.

Write 0x1: Enables the port to be sensitive to device disconnects as
wake-up events.

WCE

Wake on Connect Enable

3353

SWPU177N – December 2009 – Revised November 2010

High-Speed USB Host Subsystem and High-Speed USB OTG Controller

«
...
3351
3352
3353
3354
3355
...
»

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands