Texas Instruments OMAP36 Series Technical Reference Manual Download Page 1802

Page: 1802 / 3738

Public Version

Display Subsystem Use Cases and Tips

www.ti.com

Table 7-96. Configure DISPC_CONTROL (continued)

Comments

Registers

Value

The hardware has finished updating the internal shadow
registers of the pipeline(s) connected to the LCD output using

DISPC_CONTROL

[5] GOLCD

0x0

the user values. The hardware resets the bit when the update
completes.

Active matrix display operation mode

DISPC_CONTROL

[3] STNTFT

0x1

LCD interface is disabled.

DISPC_CONTROL

[0] LCDENABLE

0x0

The input image is converted from UYVY into RGB (see

Table 7-97

) :

Table 7-97. Configure DISPC_VID1_ATTRIBUTES

Comments

Registers

Value

Row of VIDn will not be read twice.

DISPC_VID1_ATTRIBUTES[18] VIDROWREPEATENABLE

0x0

8 x 32-bit bursts

DISPC_VID1_ATTRIBUTES[15:14] VIDBURSTSIZE

0x1

Full range selected: Y is not modified before the

DISPC_VID1_ATTRIBUTES[11] VIDFULLRANGE

0x1

color space conversion.

Enable color space conversion CbYCr to RGB.

DISPC_VID1_ATTRIBUTES[9] VIDCOLORCONVENABLE

0x1

UYVY

DISPC_VID1_ATTRIBUTES[4:1] VIDFORMAT

0xB

Video disabled

DISPC_VID1_ATTRIBUTES[0] VIDENABLE

0x0

7.6.4.5

Enable Video Mode Using the DISPC Video Port

Table 7-98

lists the steps to enable DISPC to send frames continuously.

Table 7-98. Enable DISPC

Steps

Registers

Value

Set up long packet header

DSI_VC0_LONG_PACKET_HEADER[31:0]

0x0005 A03E

Enable VC0.

DSI_VC0_CTRL[1] VC_EN

0x1

Enable IF.

DSI_CTRL

[0] IF_EN

0x1

Wait until IF_EN

≠

DSI_CTRL

[0] IF_EN

Read 0x0

Enable VID1.

DISPC_VID1_ATTRIBUTES[0] VIDENABLE

0x1

Enable LCD interface.

DISPC_CONTROL

[0] LCDENABLE

0x1

Enable GOLCD.

DISPC_CONTROL

[5] GOLCD

0x1

Wait until GOLCD = 0.

DISPC_CONTROL

[5] GOLCD

Read 0x0

7.6.5 DSI Command Mode Using the DISPC Video Port

This section presents some generic use cases and tips for setting the modules of the display subsystem.

7.6.5.1

Display Subsystem Use Cases and Tips

This section explains the basic programming model of command mode using the DISPC video port.

The DSI interface is connected to an external MIPI DISPC using the following parameters:

•

One data lane: NDL = 1

•

Clock lane at 150 MHz (DSI_DDR_CLK)

•

LCD size is 640 x 480:

–

480 PPL

–

680 LPP

•

DISPC input format: YUV

•

DISPC output format: RGB888 (24 BPP)

•

Word Count: WC = 3 x PPL

•

DSS2_ALWON_FLCK = 26 MHz used as a reference clock for DSI PLL

1802

Display Subsystem

SWPU177N – December 2009 – Revised November 2010

«
...
1800
1801
1802
1803
1804
...
»

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Texas Instruments OMAP36 Series, Technical Reference Manual, Page: 1802 / 3738

Search results

Summary of Contents for OMAP36 Series

Reviews: