Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1763 / 3738

background image

DP/DN

TXCLKESC

DIRECTION

LP state driven by remote LPTX
LP state driven by DSI PHY LPTX

DSI PHY LPRX detects turnaround request pattern
(11 - 10 - 00 - 10 - 00)

2*T

<= T

<= 3*T

LPX

TA-SURE

LPX

T

= 5*T

TA-GET

LPX

LP-11

LP-10

LP-00

LP-10

LP-00

LP-00

LP-00 LP-00 LP-00

LP-11

LP-10

LP-00

LP-00

dss-402

Public Version

www.ti.com

Display Subsystem Basic Programming Model

Figure 7-143. Turn-Around Request in Receive Mode

If the line stays in LP-00 for a time T

TA-SURE

, DSI PHY accepts the turn-around request, changes the

direction, transmits LP-00 for a time T

TA-GET

, and then transmits the acknowledgment pattern LP-10,

followed by the STOP state.

This completes the turn-around procedure. The T

TA-SURE

and T

TA-GET

timing parameters are programmable

through DSS.

DSI_PHY_REGISTER1

in number of TxClkEsc clocks:

•

T

TA-SURE

can be configured in the [28:27] REG_TTASURE bit field.

•

T

TA-GET

can be configured in the [26:24] REG_TTAGET bit field.

7.5.6.4.5 Other DSI_PHY Transmission and Reception

The timing of the following sequences defined in the DSI_PHY protocol cannot be programed by users:
•

Low-power data transmission

•

Escape mode trigger command transmission

•

ULP state command transmission on data lanes

•

ULP state transmission on clock lane

•

Low-power data in receive mode

•

Low-power trigger in receive mode

•

ULP state command on clock lane in receive mode

•

ULP state command on data lane in receive mode

7.5.6.5

Error Handling

A dedicated register for the DSI complex I/O, DSS.

DSI_COMPLEXIO_IRQSTATUS

, indicates the state

of each error provided by the DSI complex I/O error signals. The DSI_PHY reports the following errors:

•

DSI_COMPLEXIO_IRQSTATUS

[7:5] ERR_ESCi_IRQ: ERRESC is asserted if an

unrecognized Escape entry command is received. This remains high until the next change in the
line state.

•

DSI_COMPLEXIO_IRQSTATUS

[2:0] ERRSYNCESCi_IRQ: If the number of bits received

during a low-power data transmission is not a multiple of eight when the transmission ends,
ERRSYNCESC is made high and remains high until the next change in line state.

•

DSI_COMPLEXIO_IRQSTATUS

[12:10] ERRCONTROLi_IRQ: ERRCONTROL is asserted if

an incorrect line state sequence is detected. For example, if a turn-around request or escape mode
request is immediately followed by a Stop state instead of the required Bridge state, this signal is
asserted and remains asserted until the next change in the line state.

1763

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1761
1762
1763
1764
1765
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Brand: Jabra Pages: 15

DR-4100P Series

Brand: Idis Pages: 30

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

Brand: NEC Pages: 6

Brand: LORD Pages: 9

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

Brand: IEI Technology Pages: 3

iW-RainboW-G30D

Brand: iWave Pages: 89

APS6-400 Series

Brand: Eaton Pages: 114

kontron COMe-cEL6

Brand: S&T Pages: 99

Brand: IFM Electronic Pages: 14

Brand: AMD Pages: 45

Brand: TRENDnet Pages: 12

Bluespoon 17-1000

Brand: Radio Shack Pages: 1

Brand: Wyse Pages: 8

Brand: Accusys Pages: 34

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands