manualshive.com logo in svg

Texas Instruments OMAP36 Series, Technical Reference Manual

Share
Download
Texas Instruments OMAP36 Series Technical Reference Manual Download Page 1685

L4/L3

VP

DISPC

DSI

protocol

DSI data/control

ADPLLv2

HSDIVIDER

2ch

Clock

PMP

I/O

SCP

Status

DFT

DSS

Control

PMP

DSI_PHY

2ch

HSDIVIDER

ADPLLM

DSI PLL

control

Functional

Clocks

dss-179

Public Version

www.ti.com

Display Subsystem Functional Description

Figure 7-103. DSI PLL Controller Overview

NOTE:

The DSI PLL controller module does not have an interface to L4 interconnect. The

programmable features are managed by registers mapped into the DSI protocol engine.

7.4.4.2

DSI PLL Controller Architecture

The DSI PLL is an ADPLLM module. The pixel clock (PCLK) frequency range is 2 to 68.25 MHz. This may
be divided by 2. This is performed by setting the DSS.

DSI_PLL_CONFIGURATION2

[12]

DSI_PLL_HIGHFREQ bit to 1.

Figure 7-104

shows the internal DSI PLL reference diagram.

1685

SWPU177N – December 2009 – Revised November 2010

Display Subsystem

Copyright © 2009–2010, Texas Instruments Incorporated

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands