Texas Instruments OMAP36 Series Technical Reference Manual Download | Manualshive

Page: 1537 / 3738

background image

Public Version

www.ti.com

Camera ISP Register Manual

Table 6-661. CSI2_COMPLEXIO1_IRQENABLE

Address Offset

0x0000 0060

Physical Address

Instance

See

See

Description

INTERRUPT ENABLE REGISTER - All errors from associated PHY

Type

RW

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

RESERVED

ERRESC5

ERRESC4

ERRESC3

ERRESC2

ERRESC1

ERRSOTHS5

ERRSOTHS4

ERRSOTHS3

ERRSOTHS2

ERRSOTHS1

STATEULPM5

STATEULPM4

STATEULPM3

STATEULPM2

STATEULPM1

ERRCONTROL5

ERRCONTROL4

ERRCONTROL3

ERRCONTROL2

ERRCONTROL1

ERRSOTSYNCHS5

ERRSOTSYNCHS4

ERRSOTSYNCHS3

ERRSOTSYNCHS2

ERRSOTSYNCHS1

STATEALLULPMEXIT

STATEALLULPMENTER

Bits

Field Name

Description

Type

Reset

31:27

RESERVED

Write 0s for future compatibility. Read returns 0.

R

0x00

26

STATEALLULPMEXIT

At least one of the active lanes has exit the ULPM

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

25

STATEALLULPMENTER

All active lanes are entering in ULPM.

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

24

STATEULPM5

Lane #5 in Ultra Low Power Mode

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

23

STATEULPM4

Lane #4 in Ultra Low Power Mode

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

22

STATEULPM3

Lane #3 in Ultra Low Power Mode

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

21

STATEULPM2

Lane #2 in Ultra Low Power Mode

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

20

STATEULPM1

Lane #1 in Ultra Low Power Mode

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

19

ERRCONTROL5

Control error for lane #5

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

18

ERRCONTROL4

Control error for lane #4

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

17

ERRCONTROL3

Control error for lane #3

RW

0

0x0: Event is masked

0x1: Event generates an interrupt when it occurs

1537

SWPU177N – December 2009 – Revised November 2010

Camera Image Signal Processor

Copyright © 2009–2010, Texas Instruments Incorporated

«
...
1535
1536
1537
1538
1539
...
»

Summary of Contents for OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OMAP36 Series

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: Idis Pages: 31

Brand: hilscher Pages: 154

Brand: T.A Pages: 11

ZyXEL ZyAIR B-120

Brand: ZyXEL Communications Pages: 20

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: A.E.B. Pages: 28

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

Brand: Beckhoff Pages: 84

Brand: Intel Pages: 51

Brand: Mitsubishi Pages: 188

Texas Instruments 6711 DSK

Brand: National Instruments Pages: 2

Brand: Waveshare Pages: 23

Brand: Billion Pages: 8

Brand: InfoStor Pages: 6

Brand: nRichDX Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands