manualshive.com logo in svg

Texas Instruments Errata MSP430F6736A, Manual

Share
Download
Texas Instruments Errata MSP430F6736A Manual Download Page 1

Errata

MSP430F6736A Microcontroller

ABSTRACT

This document describes the known exceptions to the functional specifications (advisories).

Table of Contents

1 Functional Advisories

............................................................................................................................................................

2

2 Preprogrammed Software Advisories

..................................................................................................................................

2

3 Debug Only Advisories

..........................................................................................................................................................

3

4 Fixed by Compiler Advisories

...............................................................................................................................................

3

5 Nomenclature, Package Symbolization, and Revision Identification

................................................................................

4

5.1 Device Nomenclature.........................................................................................................................................................

4

5.2 Package Markings..............................................................................................................................................................

4

5.3 Memory-Mapped Hardware Revision (TLV Structure).......................................................................................................

5

6 Advisory Descriptions

............................................................................................................................................................

6

7 Revision History

...................................................................................................................................................................

24

www.ti.com

Table of Contents

SLAZ646S – FEBRUARY 2015 – REVISED MAY 2021

Submit Document Feedback

MSP430F6736A Microcontroller

1

Copyright © 2021 Texas Instruments Incorporated

Summary of Contents for Errata MSP430F6736A


























Reviews:

No comments

Brands by name

Popular brands

Load more brands