Texas Instruments EMIF16 User Manual Download

Page: 53 / 63

4.20 NAND Flash 4-Bit ECC 1 Register (NANDF4BECC1R)

SPRUGZ3A—May 2011

KeyStone Architecture External Memory Interface (EMIF16) User Guide

4-19

Submit Documentation Feedback

Chapter 4—Registers

www.ti.com

4.20 NAND Flash 4-Bit ECC 1 Register (NANDF4BECC1R)

The NAND Flash 4-Bit ECC 1 register is shown in

Figure 4-13

and described in

Table 4-14

Figure 4-13

NAND Flash 4-Bit ECC 1 Register (NANDF4BECC1R)

Reserved

4BIT_ECC_VAL2

Reserved

4BIT_ECC_VAL1

R - 0x0

Table 4-14

NAND Flash 4-Bit ECC 1 Register (NANDF4BECC1R) Details

Bit

Field

Value

Description

31-26

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this
field has no effect

25-16

4BIT_ECC_VAL2

0x0

4-Bit ECC or syndrome value 2 calculated while writing or reading NAND
Flash.

15-10

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this
field has no effect

9-0

4BIT_ECC_VAL1

0x0

4-Bit ECC or syndrome value 1 calculated while writing or reading NAND
Flash.

End of Table 4-14

Summary of Contents for EMIF16
































































Search results

Summary of Contents for EMIF16

Reviews:

Related manuals for EMIF16

Brands by name

Popular brands

Texas Instruments EMIF16, User Manual

Search results

Summary of Contents for EMIF16

Reviews:

Related manuals for EMIF16

Brands by name

Popular brands