manualshive.com logo in svg

Texas Instruments DS125DF1610, User Manual, Page: 14 / 15

Share
Download
Texas Instruments DS125DF1610 User Manual Download Page 14

Revision History

www.ti.com

14

SNLU159B – April 2014 – Revised September 2018

Submit Documentation Feedback

Copyright © 2014–2018, Texas Instruments Incorporated

Revision History

Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from A Revision (January 2017) to B Revision

...............................................................................................

Page

•

Changed J193 all pins open to tie 1-2 and 3-4

........................................................................................

4

Changes from Original (April 2014) to A Revision

..........................................................................................................

Page

•

Changed picture in

Figure 1

.............................................................................................................

3

•

Changed sections 2-15 from supporting Analog Launch Pad to Sigcon Architect

...............................................

4

Summary of Contents for DS125DF1610
















Reviews:

No comments