background image

User’s Guide

DRV8317HEVM User's Guide

ABSTRACT

This document is provided with the 

DRV8317HEVM customer evaluation module (EVM)

 to evaluate the 

DRV8317 4.5-V to 20-V Three-Phase Smart Gate Driver

. This User's Guide details the implementation of the 

EVM and shows how to set up and power the board with the 

LAUNCHXL-F280049C (C2000 Piccolo MCU 

F280049C LaunchPad™ development kit)

.

Note

The DRV8317HEVM comes automatically populated with and configured for the DRV8317H hardware 
device. It is also compatible for the DRV8317S variant, but the user will need to modify the board to 
make it compatible for the SPI variant (see 

Section 4.4

).

Table of Contents

1 Cautions and Warnings

..........................................................................................................................................................

2

2 Introduction

.............................................................................................................................................................................

3

3 Quick Start Guide

....................................................................................................................................................................

4

4 Hardware and Software Overview

.........................................................................................................................................

5

4.1 Hardware Connections Overview – DRV83 LAUNCHXL-F280049C...............................................................

5

4.2 Connection Details.............................................................................................................................................................

5

4.3 LED Lights..........................................................................................................................................................................

7

4.4 DRV8317HEVM Configurability – Jumpers and Resistors.................................................................................................

8

5 Hardware Setup

....................................................................................................................................................................

14

6 Firmware and GUI Application

.............................................................................................................................................

15

6.1 C2000 InstaSPIN Universal GUI......................................................................................................................................

15

6.2 Motor Identification...........................................................................................................................................................

15

6.3 Sensorless-FOC Commutation........................................................................................................................................

16

6.4 Torque Control, Speed Control, and Advanced Modulation Techniques..........................................................................

17

6.5 SPI Communication (DRV8317S only).............................................................................................................................

17

7 Schematics

............................................................................................................................................................................

19

7.1 Main Supply.....................................................................................................................................................................

19

7.2 DRV8317H/S....................................................................................................................................................................

20

7.3 3.3V Buck Regulator and VREF.......................................................................................................................................

21

7.5 LaunchPad Connections..................................................................................................................................................

22

7.6 Connectors & Interface....................................................................................................................................................

22

7.7 Status LEDs, Voltage Sense, and Protection...................................................................................................................

23

8 Revision History

...................................................................................................................................................................

23

Trademarks

All trademarks are the property of their respective owners.

www.ti.com

Table of Contents

SLVUCL3 – DECEMBER 2022

Submit Document Feedback

DRV8317HEVM User's Guide

1

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for DRV8317HEVM






























Reviews: