Texas Instruments bq51010BEVM-764, User Manual

Page: 18 / 26

Layout and Bill of Material
www.ti.com
Table 3. bq51010BEVM-764 Bill of Materials (continued)
COUNT
001 002 003 004 005 RefDes Value Description Size Part Number MFR
1 1 1 1 1 R16 5k Potentiometer, 1/4 in. Cermet, 12-Turn, Top-Adjust 0.25x0.17 3266W-1-502LF Bourns
0 0 1 0 0 R17 20K Resistor, Chip, 1/16W, 1% 0603 Std Std
0 1 0 1 0 R17 42.2K Resistor, Chip, 1/16W, 1% 0603 Std Std
0 0 0 0 1 R17 36K Resistor, Chip, 1/16W, 1% 0603 Std Std
15 15 15 15 15 TP1, TP2, TP3, TP4, TP5, TP6, TP7, 5000 Test Point, Red, Thru Hole Color Keyed 0.100 x 0.100 inch 5000 Keystone
TP8, TP9, TP10, TP11, TP12, TP16,
TP17, TP18
3 3 3 3 3 TP13, TP14, TP15 5001 Test Point, Black, Thru Hole Color Keyed 0.100 x 0.100 inch 5001 Keystone
1 0 0 0 0 U1 bq51013AYFP IC, Wirless Secondary-Side Power Controller DSBGA bq51013AYFP TI
0 1 0 0 0 U1 bq51050BYFP IC, Wirless Secondary-Side Power Controller and Battery Charger DSBGA bq51050BYFP TI
0 0 1 0 0 U1 bq51013BYFP IC, Wirless Secondary-Side Power Controller DSBGA bq51013BYFP TI
0 0 0 1 0 U1 bq51051BYFP IC, Wirless Secondary-Side Power Controller and Battery Charger DSBGA bq51013BYFP TI
0 0 0 0 1 U1 bq51010BYFP IC, Wirless Secondary-Side Power Controller DSBGA bq51013BYFP TI
5 5 5 5 5 -- Shunt, 100-mil, Black — See note 6 929950-00 3M
1 1 1 1 1 -- PCB, 2.1" x 2.1" x 0.031" HPA764 Any
1 1 1 1 1 -- Case Modified Polycase LP-11B with 4 screws — See note 7 J-6838A Polycase
1 1 1 1 0 -- Coil, RX with Attractor IWAS-4832FF-50 Vishay
WR-483250-15M2-G TDK
760308103204 Wyurth
0 0 0 0 1 Coil, RX with Attractor — See note 8 IWAS4832ECEB160J50 Vishay
1 1 1 1 1 Tape segment, Low Static Polyimide Film — See note 9 1.5" x 2.3" 5419-1 1/2" 3M
1 1 1 1 1 Label Label Thermal Label — See note 10 THT-53-423-3 Brady
Notes: 1. These assemblies are ESD sensitive, observe ESD precautions.
2. These assemblies must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.
5. Tape "Coil, RX" into bottom of case, centered, coil side down, lead wires passing through milled groove.
6. Install Shunts on:
JP1 : (Only for HPA764-001, 003, & 005) between EN1/TERM and JP4 : between Pull-up and Vz
LOW
JP2 : between EN2 and LOW JP5 : (Only for HPA764-002 and HPA764-004) between two ends
JP3 : between TS and DIS
7. Install PCB in case using screws provided with case
8. WR483225-16M6-TI3 from TDK coil can also be used as second option.
9. Used to secure RX coil to case. Cut tape section from 36 yard roll identified in part number field.
10. Install label on back of PCB near J6 on the top edge of the PCB after final wash (box). Text shall be 8 pt font or lower. Text shall be per Table 1 . The ref designators should not be hidden by the label.
Table 1
Assembly Number Text
HPA764-001 bq51013AEVM-764
HPA764-002 bq51050BEVM-764
HPA764-003 bq51013BEVM-764
18 bq51010BEVM-764 Evaluation Module (WCSP Package) SLUUAE3A – August 2013 – Revised December 2013
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated