background image

User’s Guide

BQ25180 EVM User's Guide

ABSTRACT

This user's guide provides detailed testing instructions for the BQ25180 evaluation module (EVM). Also included 
are descriptions of the necessary equipment, equipment setup, procedures, the printed-circuit board layouts, 
schematics, and the bill of materials (BOM).

Throughout this user's guide, the abbreviation 

EVM, BQ25180EVM,

 and the term evaluation module are 

synonymous with the BQ25180 evaluation module, unless otherwise noted.

Table of Contents

1 Introduction

.............................................................................................................................................................................

2

1.1 Features.............................................................................................................................................................................

2

2 EVM Setup

...............................................................................................................................................................................

2

3 EVM Connectors and Test Points

..........................................................................................................................................

4

4 Testing Procedures

.................................................................................................................................................................

5

4.1 Equipment..........................................................................................................................................................................

5

4.2 Charge Mode.....................................................................................................................................................................

5

4.3 Ship Mode..........................................................................................................................................................................

8

5 PCB Layouts

............................................................................................................................................................................

9

6 Schematic

..............................................................................................................................................................................

10

7 Bill of Materials

.....................................................................................................................................................................

13

8 Revision History

...................................................................................................................................................................

16

List of Figures

Figure 4-1. BQ25180 EVM Connections.....................................................................................................................................

5

Figure 4-2. TI Charger GUI Device Selection..............................................................................................................................

6

Figure 4-3. BQ25180EVM Connected.........................................................................................................................................

7

Figure 4-4. Quick Start.................................................................................................................................................................

7

Figure 4-5. Register Map.............................................................................................................................................................

8

Figure 4-6. SHIP_RST Register..................................................................................................................................................

8

Figure 5-1. Top Overlay...............................................................................................................................................................

9

Figure 5-2. Top Solder.................................................................................................................................................................

9

Figure 5-3. Top Layer...................................................................................................................................................................

9

Figure 5-4. Bottom Layer.............................................................................................................................................................

9

Figure 5-5. Bottom Solder............................................................................................................................................................

9

Figure 5-6. Bottom Overlay..........................................................................................................................................................

9

Figure 6-1. BQ25180EVM Schematic........................................................................................................................................

10

Figure 6-2. BQ25180EVM Jumper Connectors.........................................................................................................................

11

Figure 6-3. LDO for Other Peripherals.......................................................................................................................................

12

List of Tables

Table 2-1. Jumper Descriptions...................................................................................................................................................

2

Table 2-2. Recommended Operating Conditions.........................................................................................................................

3

Table 3-1. Factory Jumper Settings.............................................................................................................................................

4

Table 7-1. Bill of Materials..........................................................................................................................................................

13

Trademarks

All trademarks are the property of their respective owners.

www.ti.com

Table of Contents

SLUUCH5A – AUGUST 2021 – REVISED JANUARY 2022

Submit Document Feedback

BQ25180 EVM User's Guide

1

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for BQ25180























Reviews: