background image

To
Computer
USB port

USB

Interface

Adapter

I/O

USB

T

exasInstruments

©2006

10-pin
Ribbon
Cable

To EVM

Test Summary

www.ti.com

2.2.4

Meters

Two equivalent voltage meters and two equivalent current meters. The current meters must be able to
measure 2-A current.

2.2.5

Computer

A computer with at least one USB port and a USB cable. The bq24153_6_8 evaluation software must be
properly installed.

2.2.6

HPA172 Communication Kit (USB TO GPIO)

A HPA172 USB to I2C communication kit.

2.2.7

Software

Download BQ24153_6_8Setup.zip from the charger's product folder, unzip the file and double-click on the
“SETUP.EXE” file. Follow the installation steps.

2.3

Recommended Test Equipment Setup

1. Set Power Supply #1 for 5 V ± 100 mVdc, 2-A. ±0.1-A current limit, and then turn off supply.

2. Connect the output of Power Supply #1 in series with a current meter (multimeter) to J1 (DC+, DC–).

3. Connect a voltage meter across J1 (DC+, DC–).

4. Connect the Load #2 in series with a current meter (multimeter) to J2 (BAT+, BAT–). Ensure that a

voltage meter is connected across J2 (BAT+, BAT–). Turn on the Load #2. Use the constant voltage
mode. Set the output voltage to 2.5 V.

5. Turn off Load #2.

6. Connect J5 to HPA172 kit by the 10-pin ribbon cable. Connect the USB port of the HPA172 kit to the

USB port of the computer. The connections are shown in

Figure 1

.

Figure 1. Connections of HPA172 Kit

7. Install jumpers per

Table 1

Table 1. Factory Jumper Settings

Spin

JMP1

JMP2

JMP3

JMP4

JMP5

HPA256-001

(-LED-) ON

(-LO-) ON

OFF

(-LO-) ON

ON

(bq24153A)

HPA256-002

(-LED-) ON

(-HI-) ON

OFF

(-LO-) ON

ON

(bq24156A)

4

bq24153A/56A/57/58/59 Fully Integrated, Switch-Mode, One-Cell, Li-Ion Charger

SLUU453C – November 2010 – Revised May 2013

With Full USB Compliance and USB-OTG Support EVM

Submit Documentation Feedback

Copyright © 2010–2013, Texas Instruments Incorporated

Summary of Contents for bq24153A



















Reviews: