manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

Share
Download
Texas Instruments AM1808 Technical Reference Manual Download Page 1595

www.ti.com

Registers

1595

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Serial Bus OHCI Host Controller

33.3.11 HC Head Bulk Register (HCBULKHEADED)

The HC head bulk register (HCBULKHEADED) defines the physical address of the head endpoint
descriptor (ED) on the bulk ED list. HCBULKHEADED is shown in

Figure 33-12

and described in

Table 33-12

.

Figure 33-12. HC Head Bulk Register (HCBULKHEADED)

31

16

BHED

R/W-0

15

4

3

0

BHED

Reserved

R/W-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 33-12. HC Head Bulk Register (HCBULKHEADED) Field Descriptions

Bit

Field

Value

Description

31-4

BHED

0-FFF FFFFh Physical address of the head ED on the bulk ED list. This field represents bits 31-4 of the physical

address of the head ED on the bulk ED list. EDs are assumed to begin on a 16-byte aligned
address, so bits 3-0 of this pointer are assumed to be 0. For the restrictions on physical
addresses, see

Section 33.2.7

.

3-0

Reserved

0

Reserved

33.3.12 HC Current Bulk Register (HCBULKCURRENTED)

The HC current bulk register (HCBULKCURRENTED) defines the physical address of the next endpoint
descriptor (ED) on the bulk ED list. HCBULKCURRENTED is shown in

Figure 33-13

and described in

Table 33-13

.

Figure 33-13. HC Current Bulk Register (HCBULKCURRENTED)

31

16

BCED

R/W-0

15

4

3

0

BCED

Reserved

R/W-0

R-0

LEGEND: R/W = Read/Write; R = Read only; -

n

= value after reset

Table 33-13. HC Current Bulk Register (HCBULKCURRENTED) Field Descriptions

Bit

Field

Value

Description

31-4

BCED

0-FFF FFFFh Physical address of the current ED on the bulk ED list. This field represents bits 31-4 of the

physical address of the next ED on the bulk ED list. EDs are assumed to begin on a 16-byte
aligned address, so bits 3-0 of this pointer are assumed to be 0. For the restrictions on physical
addresses, see

Section 33.2.7

.

A value of 0 indicates that the USB1.1 host controller has reached the end of the bulk ED list
without finding any transfers to process. This register is automatically updated by the USB1.1 host
controller.

3-0

Reserved

0

Reserved

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands