manualshive.com logo in svg

Texas Instruments AM1808, Technical Reference Manual

The Texas Instruments AM1808 User Manual is a comprehensive guide designed to assist users in getting the most out of their AM1808 product. This manual provides step-by-step instructions, troubleshooting tips, and detailed information about the device's features and functionalities. Download your free copy exclusively from manualshive.com today.

Share
Download
background image

Processor

physical
address

Processor

virtual

address

Processor

MMU

00000000h

FFFFFFFFh

www.ti.com

Architecture

1585

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Copyright © 2013–2016, Texas Instruments Incorporated

Universal Serial Bus OHCI Host Controller

33.2.5 OHCI Interrupts

The USB1.1 host controller is controlled by the ARM. It has the ability to interrupt the processor.

33.2.6 USB1.1 Host Controller Access to System Memory

The USB1.1 module needs to access system memory to read and write the OHCI data structures and
data buffers associated with USB traffic. The switch fabric allows the USB1.1 host controller to access
system memory.

33.2.7 Physical Addressing

Transactions on the internal bus use physical addresses, so all system memory accesses initiated by the
USB1.1 host controller must use physical addresses. The CPU can be configured to use virtual
addressing. In this case, software manipulates virtual addresses that may or may not be identical to
physical addresses. When virtual addressing is used, system software must perform the appropriate
virtual address to physical address and physical address to virtual address conversions when
manipulating the USB1.1 host controllers data structures and pointers to those data structures.

Figure 33-1

shows the virtual address to physical address conversion.

Figure 33-1. Relationships Between Virtual Address Physical Address

Summary of Contents for AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AM1808

Patton electronics 2888 Getting Started Manual preview
2888
Brand: Patton electronics Pages: 51
NXP Semiconductors TWR-SB0410-36EVB User Manual preview
TWR-SB0410-36EVB
Brand: NXP Semiconductors Pages: 26
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Brand: Direct IP Pages: 76
Intel SRCSASBB8I - RAID Controller Hardware User'S Manual preview
SRCSASBB8I - RAID Controller
Brand: Intel Pages: 36
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Brand: IBM Pages: 74
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Brand: Mobatime Pages: 94
Akasa Venom A10 User Manual preview
Venom A10
Brand: Akasa Pages: 2
ADC The DSX Value Solution (Japanese) LDX154 (Japanese) Brochure preview
The DSX Value Solution (Japanese) LDX154
Brand: ADC Pages: 4
D-Link WCB-B11 User Manual preview
WCB-B11
Brand: D-Link Pages: 9
Nahita ZFP009 User Manual preview
ZFP009
Brand: Nahita Pages: 9
Barefoot nbn HFC Connection Manual preview
nbn HFC
Brand: Barefoot Pages: 3
ICP GDT8123RZ Specification preview
GDT8123RZ
Brand: ICP Pages: 2
ICP GDT6111RP User Manual preview
GDT6111RP
Brand: ICP Pages: 36
Vidyo HD-220 Getting Started preview
HD-220
Brand: Vidyo Pages: 2
SilverStone tundra series User Manual preview
tundra series
Brand: SilverStone Pages: 24
Peavey X-Frame 88 Specifications preview
X-Frame 88
Brand: Peavey Pages: 8

Brands by name

Popular brands

Load more brands